Bedienungsanleitung DeWalt dw 498 (Seite 24 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

390552

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

• Remove both screws (12) from the diamond

guard and disassemble the front plate (13).

• Insert the spindle through the hole in the rear

plate (14) and tighten the three screws (10).

Make sure the slots (15) in the rear plate and the

retention disc (16) coincide.

• Rotate the angle grinder to the required position

and tighten the lock nut (11).

• Fit an appropriate diamond cutting disc (see below).

• Mount the front plate (13). Make sure that the dust

extraction outlet (17) is properly caught in the

opening between front (13) and rear plate (14).

Hook the cam behind the ruler stop (18) in the base

plate to make sure the spring (19) can move freely.

• Refit the screws (12).

• To remove the diamond guard, proceed in

reverse order.

Fitting and removing a grinding wheel or cutting

disc (fig. D)

• Place the tool on a table, guard up.

• Fit the spacer (20) correctly onto the spindle (5).

• Place the grinding wheel or cutting disc on the

spacer.

• Screw the threaded flange (21) onto the spindle (5).

• Press the spindle lock (4) and rotate the grinding

wheel or cutting disc until it locks in position.

• Tighten the threaded flange (21) with the two-pin

spanner supplied.

• Release the spindle lock.

• To remove the grinding wheel or cutting disc,

loosen the threaded flange (21) with the two-pin

spanner.

Fitting a wire cup brush

• Screw the wire cup brush directly onto the

spindle without the use of the spacer and

threaded flange.

Mounting the side handle (fig. E)

• For grinding, screw the side handle (6) tightly into

one of the holes (8) on either side of the gear case.

• For cutting, screw the side handle (6) tightly into

the top hole (7).

DW491 + DE8501 - Mounting the round handle

DE8502 (option) (fig. F)

• Remove the side handle.

ENGLISH

Conductor size (mm2) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0-2.0 66 66 610

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Voltage drops

Inrush currents cause short-time voltage drops.

Under unfavourable power supply conditions, other

equipment may be affected.

If the system impedance of the power supply is lower

than 0.25 ø, disturbances are unlikely to occur.

Assembly and adjustment

Prior to assembly and adjustment always

unplug the tool.

Mounting and removing the guard (fig. B)

• Place the angle grinder on a table, spindle up.

• Mount the guard to the tool using the three

screws (10) with star washers.

• Rotate the guard to the required position and

tighten the lock nut (11).

• To remove the guard, loosen the three screws (10).

DW491 - Mounting and removing the diamond

guard DE8501 (option) (fig. C)

The diamond guard DE8501 has been designed for

depth adjustment and efficient dust extraction.

• Remove the guard from the angle grinder and

place the tool on a table, spindle up.

DWLAG.P65 17-09-2001, 08:4924

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt dw 498 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info