Bedienungsanleitung DeWalt dw 566 k (Seite 26 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

387206

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

en - 5

• Push the bit down and turn it slightly until it fits

into the slots.

• Pull on the bit to check if it is properly locked.

The hammering function requires the bit to be

able to move axially several centimetres when

locked in the tool holder.

• To remove a bit pull back the tool holder locking

sleeve (9) and pull out the bit.

Fitting the side handle (fig. D)

The side handle (5) can be fitted to suit both RH-

and LH-users.

Always use the tool with the side handle

properly assembled.

• Loosen the side handle.

• For RH-users, slide the side handle clamp over

the collar behind the tool holder, handle at the

left.

• For LH-users, slide the side handle clamp over the

collar behind the tool holder, handle at the right.

• Rotate the side handle to the desired position

and tighten the handle.

Setting the drilling depth (fig. E)

• Insert the required drill bit.

• Slacken the side handle (5).

• Fit the depth adjustment rod (6) through the hole

in the side handle clamp.

• Adjust the drilling depth as shown.

• Tighten the side handle.

Forward/Reverse-lever (fig. F)

• Push the forward/reverse-lever (3) to the LH-side

for forward (RH) rotation. See arrows on tool.

• Push the forward/reverse-lever (3) to the RH-side

for reverse (LH) rotation.

Always wait until the motor has come to

a complete standstill before changing the

direction of rotation.

Replacing the dust cover (fig. C)

The dust cover (7) prevents dust ingress into the

mechanism. Replace a worn dust cover

immediately.

• Pull back the tool holder locking sleeve (9) and

pull the dust cover (7) off.

• Fit the new dust cover.

• Release the tool holder locking sleeve.

How to fit the Chuck Adapter & Chuck

• Unplug the tool.

• Screw the keyed chuck onto the threaded end of

the chuck adapter.

• Insert the connected chuck and adapter in the

tool as though it were a standard SDS-plus

bit.

• Always tighten the accessory into the keyed

chuck using all three holes.

• To remove the chuck, proceed as for removing a

standard SDS-plus

bit.

• Never use the keyed chuck in hammer

drilling mode.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool

(approx. 2-3 kg). Excessive force does

not speed up drilling but decreases tool

performance and may shorten tool life.

• Do not drill or drive too deep to prevent

damage to the dust cover.

Switching ON and OFF (fig. A)

• To run the tool, press the variable speed switch (1).

The pressure exerted on the variable speed

switch determines the tool speed.

• If necessary, press the lock-on button (2) for

continuous operation and release the variable

speed switch. The lock-on button works only in

full speed, forward rotation.

• To stop the tool, release the variable speed switch.

• To stop the tool in continuous operation, press

the variable speed switch briefly and release it.

Always switch OFF the tool when work is finished

and before unplugging.

Hammer drilling (fig. A)

• Select the hammer drilling mode (4).

• Insert the appropriate SDS-plus

bit. For best

results use high quality carbide-tipped bits.

• Mark the spot where the hole is to be drilled.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt dw 566 k Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info