Bedienungsanleitung DeWalt dw 567 k (Seite 26 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

387207

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

en - 5

• Fit the depth adjustment rod (6) through the hole

in the side handle clamp.

• Adjust the drilling depth as shown.

• Tighten the side handle.

Forward/Reverse-lever (fig. F)

• Push the forward/reverse-lever (3) to the LH-side

for forward (RH) rotation. See arrows on tool.

• Push the forward/reverse-lever (3) to the RH-side

for reverse (LH) rotation.

Always wait until the motor has come to

a complete standstill before changing the

direction of rotation.

Replacing the dust cover (fig. C)

The dust cover (7) prevents dust ingress into the

mechanism. Replace a worn dust cover immediately.

• Pull back the tool holder locking sleeve (9) and

pull the dust cover (7) off.

• Fit the new dust cover.

• Release the tool holder locking sleeve.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool

(approx. 2-3 kg). Excessive force does

not speed up drilling but decreases tool

performance and may shorten tool life.

• Do not drill or drive too deep to prevent

damage to the dust cover.

Switching ON and OFF (fig. A)

• To run the tool, press the variable speed switch (1).

The pressure exerted on the variable speed

switch determines the tool speed.

• If necessary, press the lock-on button (2) for

continuous operation and release the variable

speed switch. The lock-on button works only in

full speed, forward rotation.

• To stop the tool, release the variable speed switch.

• To stop the tool in continuous operation, press

the variable speed switch briefly and release it.

Always switch OFF the tool when work is finished

and before unplugging.

Hammer drilling (fig. A)

• Select the hammer drilling mode (4).

• Insert the appropriate SDS-plus

bit. For best

results use high quality carbide-tipped bits.

• Mark the spot where the hole is to be drilled.

• Press the tool against the workpiece.

• Switch the tool ON by pressing the variable speed

switch (1). The hammer mechanism should run

smoothly and the tool should not bounce. If

necessary, increase the pressure on the switch.

Rotary drilling (fig. A)

• Select the rotary drilling mode (4).

• Proceed as described for hammer drilling.

Special SDS-plus

adaptors with threaded

sections are available for use with standard 10 or

13 mm chucks to enable straight shank bits to

be used.

Never use standard chucks in the

hammer drilling mode.

Screwdriving (fig. A)

• Select the rotary drilling mode (4).

• Select the direction of rotation (3).

• Insert the special SDS-plus

screwdriving

adaptor for use with hexagonal screwdriver bits.

• Insert the appropriate screwdriver bit into the

adaptor. When driving slotted head screws

always use bits with a finder sleeve.

• Gently press the variable speed switch (1) to

prevent damage to the screw head. In reverse

(LH) rotation the tool speed is automatically

reduced for easy screw removal.

Chipping and chiselling

• To switch from hammer drilling to chiselling, first

insert the SDS-plus

chisel and check if it is

properly locked.

• When switching from hammer drilling mode to

chiselling mode, turn the chisel to the desired

position. If you find resistance during mode change,

turn the chisel slightly to engage the spindle lock.

• The hammer is only for light chiselling

applications.

• The forward/reverse switch must be in the

forward position when chiselling (in reverse

the unit does not reach full power).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt dw 567 k Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info