Bedienungsanleitung DeWalt dw 570 k (Seite 23 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388802

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

• Mark the spot where the hole is to be drilled.

• Place the drill bit on the spot and press the

variable speed switch (1).

• To stop the tool, release the switch.

Drilling with a core bit (fig. A)

• Set the mode selector (3) to the “hammer drilling”

position.

• Adjust the side handle (4) as required.

• Insert the appropriate core bit.

• Assemble the centerdrill into the core bit.

• Place the centerdrill on the spot and press the

variable speed switch (1). Drill until the core

penetrates into the concrete approx. 1 cm.

• Stop drilling and remove the centerdrill. Place the

core bit back into the hole and continue drilling.

• When drilling through a structure thicker than the

depth of the core bit, break away the round cylinder

of concrete or core inside the bit at regular intervals.

To avoid unwanted breaking away of concrete

around the hole, first drill a hole the diameter of the

centerdrill completely through the structure.

Then drill the cored hole halfway from each side.

Chipping and chiselling (fig. A)

• Before inserting the chisel, set the mode

selector (3) to the “hammering only with

spindle lock” position.

• Insert the appropriate chisel. To adjust the head of

the chisel to the desired angle, set the mode

selector (3) to the “bit rotation” position and rotate

the chisel by hand. Return the mode selector to

the “hammer only with spindle lock” position.

• Adjust the side handle (4) as required.

• Press the variable speed switch (1) and start

working.

• Do not use this tool to mix or pump

easily combustible or explosive fluids

(benzine, alcohol, etc.).

• Do not mix or stir inflammable liquids

labelled accordingly.

Consult your dealer for further information on the

appropriate accessories.

18 en - 5

ENGLISH

Removing and attaching the tool holder (fig. C)

• To remove the tool holder, pull the locking collar

(10) towards the front of the tool and pull the tool

holder off.

• To attach the tool holder, slide the locking collar

towards the SDS-plus

fitting, push the tool holder

onto the spindle, release the locking collar and

rotate the tool holder until it clicks into position.

A keyless 3-jawed chuck for drilling in wood, metal

and plastics is available as an accessory (DT7003).

Please contact your local DEWALT dealer for further

information.

Adjusting the side handle (fig. D)

To adjust the position of the side handle (4):

• Loosen the handle by unscrewing it (A).

• Rotate the handle to the desired position and

tighten it (B).

Always use the tool with the side handle

properly assembled.

Setting the drilling depth (fig. E)

• Insert the required drill bit as described above.

• Loosen the depth stop clamp (6).

• Fit the depth adjustment rod (5) through the hole

in the depth stop clamp.

• Adjust the drilling depth as shown.

• Tighten the depth stop clamp.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool.

Excessive force does not speed up

drilling but decreases tool performance

and may shorten tool life.

Drilling with a solid bit (fig. A)

• Set the mode selector (3) to the desired position:

hammer drilling for masonry, drilling only for

wood, metal and plastic, hammer only for

chipping and chiselling applications.

• Insert the appropriate drill bit.

• Adjust the side handle (4) as required.

• If necessary, set the drilling depth.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt dw 570 k Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info