Bedienungsanleitung DeWalt dw 62 qs (Seite 24 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

382880

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

en - 3

Check for misalignment and seizure of moving

parts, breakage of parts and any other conditions

that may affect its operation. Have damaged

guards or other defective parts repaired or

replaced as instructed.

Do not use the tool if the switch is defective.

Have the switch replaced by an authorized

DEWALT repair agent.

20 Have your tool repaired by an authorized

DEWALT repair agent

This Power Tool is in accordance with the

relevant safety regulations. To avoid danger,

electric appliances must only be repaired by

qualified technicians.

Additional safety rules for circular saws

Plugging into the mains, switching ON and OFF

• Always ensure that the Power Tool is switched

OFF before plugging into the mains.

• Remove the blade changing spanner from the

saw blade locking screw before switching ON.

• Do not switch OFF before the saw blade is

running freely.

When sawing

• Remove all nails and metal objects from the

workpiece before starting work.

• Do not attempt to saw extremely small

workpieces.

• After switching OFF, never attempt to stop the saw

blade by pressing against the side of the blade.

• Never put the saw down on a table or work

bench unless switched OFF.

• Always use the riving knife, except for inserted cuts.

Operational protection devices

• The circular saw must only be used for cutting

wood or plastic.

• Ensure that all devices screening the saw blade

are in perfect working order.

• Never jam the saw blade guards.

• Free a jammed saw blade guard immediately and

do not use the saw if the guard is jammed.

• Do not remove the riving knife.

• The riving knife should be correctly set; the

distance between the toothed rim and the riving

knife should be 2 - 5 mm and the height

difference should be 3 mm or less (fig. E).

Checking and changing the saw blade

• Only saw blades conforming to the specifications

contained in these operating instructions may be

used.

• Saw blades made of high alloy, high speed steel

(HSS steel) should not be used. Good results are

achieved using carbide-tipped or CrV saw blades.

• Only sharp saw blades in perfect working

condition should be used; cracked or bent saw

blades should be discarded and replaced at once.

• Ensure that the saw blade is securely fixed and

rotates in the correct direction.

Using in a fixed position

• When using a saw bench ensure that the width

of the sawing gap is sufficient to take the saw

blade being used.

• When cutting narrow workpieces (width less than

80 mm) longitudinally, use a rip fence guide along

the longitudinal edge.

• When sawing with the workpiece clamped tight,

devices should be used to prevent the workpiece

kicking back.

• When sawing circular sections of wood use a

device to hold the workpiece steady on both

sides of the saw blade to prevent slipping.

• Ensure that pieces of wood sawn off the

workpiece cannot be caught up by the teeth of

the saw blade and thrown in the air.

Guard against kickback

• Kickback occurs when the saw begins to stall

rapidly and is driven back towards the operator.

Release the switch immediately if the blade sticks

or the saw stalls.

• Keep the saw blades sharp.

• Support large panels near the cutting area.

• Use a fence or straight edge guide when ripping;

do not force the tool.

• Do not remove the saw from the work during a

cut while the saw blade is rotating. Release the

ON/OFF-switch and wait for the saw blade to

come to a halt.

Package contents

The package contains:

1 Circular Saw with 1 general purpose TCT blade

1 Parallel fence

1 Saw blade wrench

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt dw 62 qs Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info