Bedienungsanleitung DeWalt dw 621 qs (Seite 26 von 98) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

426996

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

Prior to operation:

• Check that the cutter is correctly installed in

the collet.

• Select the optimal speed using the electronic

speed control dial (DW621).

• Set the cutting depth.

• Connect a dust extractor.

• Make sure the plunge limiter is always locked

before switching on.

Switching on and off (fig. I)

The lock-on/lock-off switch (1) is located in the

handle on the right-hand side. The router is normally

locked in the off position.

• Switching on: press and hold down the switch

(28) to unlock the tool and subsequently squeeze

the trigger (29).

• For continuous operation, press the switch (28)

again.

• Switching off: squeeze the trigger (29) again.

Loosen the plunge limiter and allow the

router carriage to regain its rest position

before switching off.

Using the guide bushes (fig. G)

• Secure the template to the workpiece using end

clamps.

• Select and install an appropriate guide bush (26).

• Subtract the diameter of the cutter from the outside

diameter of the guide bush and divide by 2. This is

the difference between template and workpiece.

If the workpiece is not thick enough,

place it on a piece of waste wood.

Guiding off a batten

Where an edge guide cannot be used, it is also

possible to guide the router along a batten clamped

across the workpiece (with an overhang at both ends).

Freehand routing

Your router can also be used without any sort of

guide, e.g. for signwriting or creative work.

Make shallow cuts only! Use cutters with

a max. diameter of 6 mm.

Routing with pilot cutters (fig. B)

Where a parallel guide or guide bush are

inappropriate, it is possible to use pilot cutters (30)

for cutting shaped edges.

Consult your dealer for further information on the

appropriate accessories.

These include collets (6-8 mm), a depth stop for use

in inverted position, finger jointing tools for dovetail

and finger jointing jigs, dowel jointing templates,

guide bushes (17-40 mm) and guide rails in various

lengths.

Maintenance

Your DEWALT Power Tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Cleaning the dust extraction column (fig. J)

• Remove the dust extraction plug or adaptor.

• Remove the four screws (31) in the bottom of the

router base (10).

• Clean the dust extraction column.

• Reassemble the parts in reverse order.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

Keep the ventilation slots clear and regularly clean

the housing with a soft cloth.

Unwanted tools and the environment

Take your tool to an authorized DEWALT repair

agent where it will be disposed of in an

environmentally safe way.

ENGLISH

en - 6 21

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt dw 621 qs Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info