426997
25
Zoom out
Zoom in
Vorherige Seite
1/100
Nächste Seite
20
ENGLISH
en - 6
Connecting a dust extractor (fig. A & K)
The dust extraction adapter (33) consists of a main
section (34), a clamping piece (35), a cutter plate (36),
two screws (37) and two nuts (38).
Slide the clamping plate (35) onto the main
section (34) from the front.
Fit the screws (37) and nuts (38).
Insert the cutter plate (36) from the bottom and
rotate it until it clicks in place.
Mount the unit to the router base.
Connect a dust extractor hose to the dust
extraction adaptor (33).
Loosen the screw in the top of the router and fit
the hose guide as shown.
Instructions for use
Always observe the safety instructions
and applicable regulations.
Always move your Router as indicated in
fig. L (outer edges/inner edges).
Prior to operation:
Check that the cutter is correctly installed in the
collet.
Select the optimal speed using the electronic
speed control dial.
Set the cutting depth.
Connect a dust extractor.
Make sure the plunge limiter is always locked
before switching ON.
Switching ON and OFF (fig. A & G)
ON: pull the switch (1) UP.
OFF: press the switch (1) DOWN.
Loosen the plunge limiter and allow the
router carriage to regain its rest position
before switching OFF.
Using the guide bushes (fig. J)
Secure the template to the workpiece using end
clamps.
Select and install an appropriate guide bush (31).
Subtract the diameter of the cutter from the outside
diameter of the guide bush and divide by 2. This is
the difference between template and workpiece.
If the workpiece is not thick enough,
place it on a piece of waste wood.
Guiding off a batten
Where an edge guide cannot be used, it is also
possible to guide the router along a batten clamped
across the workpiece (with an overhang at both ends).
Freehand routing
Your Router can also be used without any sort of
guide, e.g. for signwriting or creative work.
Make shallow cuts only!
Use cutters with a max. diameter of 6 mm.
Routing with pilot cutters (fig. B)
Where a parallel guide or guide bush are
inappropriate, it is possible to use pilot cutters (24)
for cutting shaped edges.
Consult your dealer for further information on the
appropriate accessories.
These include collets (1/4-1/2"), a depth stop and
router table for use in inverted position, finger
jointing tools for dovetail and finger jointing jigs,
dowel jointing templates, guide bushes (17-40 mm),
guide bushes, guide bush holders and guide rails in
various lengths.
Maintenance
Your DEWALT Power Tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Lubrication
Your Power Tool requires no additional lubrication.
Cleaning
Keep the ventilation slots clear and regularly clean
the housing with a soft cloth.
25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für DeWalt dw 625 kqsu wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info