Bedienungsanleitung DeWalt DW 685 (Seite 28 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

78380

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

ENGLISH

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 60745; therefore no

earth wire is required.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

EWALT service organisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in

the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

Using an Extension Cable

If an extension cable is required, use an approved

3–core extension cable suitable for the power

input of this tool (see technical data). The minimum

conductor size is 1.5 mm

; the maximum length is

30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

Replacing the Blade (ﬁ g. 1a, 1b)

1. Remove the knurled nuts (d) and the cover

plate (c).

2. Hold the spindle using the sickle spanner and

remove the front flange by turning it clockwise.

3. Change the blade.

4. Tighten the flange securely by turning it

counterclockwise while holding the spindle with

the sickle spanner.

5. Mount the cover plate and tighten the

knurled nuts.

Adjusting the Depth of Cut (ﬁ g. 2)

The correct depth of cut for biscuit jointing is

determined by the size of the biscuit dowel:

Biscuit dowel size Depth of cut

0 8 mm

10 10 mm

20 12 mm

To set the correct depth of cut, turn the adjuster (b)

as required. The depth of cut can be read from the

scale.

Adjusting the Blade to the Panel

Thickness (ﬁ g. 3)

The fine adjuster (e) allows centring the grooving

blade in the panel edge.

1. Slacken the locking knob (n).

2. Adjust the fine adjuster (e) as required. The

setting can be read from the scale (m).

3. Tighten the locking knob.

Mounting and Adjusting the Parallel

Fence (ﬁ g. 1a)

1. Slacken the locking bolts (l).

2. Insert the rods of the parallel fence into the

corresponding holes in the base of the tool.

3. Set the parallel fence to the desired position.

4. Tighten the locking bolts.

Mounting the Mitre Fence (ﬁ g. 1a)

1. Slacken the locking bolts (l).

2. Fully insert the rods of the mitre fence into the

corresponding holes in the base of the tool.

3. Tighten the locking bolts.

Mounting the Cutting Insert

(ﬁ g. 1b, 4)

1. Remove the knurled nuts (d) and the cover

plate (c).

2. Carefully place the insert (p) in the recesses (o).

3. Mount the cover plate and tighten the

knurled nuts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW 685 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info