Bedienungsanleitung DeWalt dw 954 (Seite 26 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

387252

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

en - 5 20

ENGLISH

Using an extension cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of your charger

(see technical data). The minimum conductor size is

0.5 mm

; the maximum length is 30 m.

Assembly and adjustment

• Prior to assembly and adjustment,

always remove the battery pack.

• Always switch OFF the tool before

inserting or removing the battery pack.

Battery pack (fig. A)

Charging the battery pack

When charging the battery pack for the first time,

or after prolonged storage, it will only accept an 80%

charge. After several charge and discharge cycles,

the battery pack will attain full capacity. Always check

the mains prior to charging the battery pack. If the

mains is functioning but the battery pack does not

charge, take your charger to an authorised DEWALT

repair agent. Whilst charging, the charger and the

battery pack may become warm to touch. This is a

normal condition and does not indicate a problem.

Do not charge the battery pack at

ambient temperatures <4 °C or >40 °C.

Recommended charging temperature:

approx. 24 °C.

• To charge the battery pack (9), insert it into the

charger (11) as shown and plug in the charger.

Be sure that the battery pack is fully seated in the

charger. The red charging indicator (12) will blink.

After approx.

/2 hour, it will stop blinking and

remain on. The battery pack is now fully charged

and the charger automatically switches to

equalise mode. After approx. 4 hours, it will

switch to maintenance charge mode.

The battery pack can be removed at any time or

left in the connected charger indefinitely.

• The red charging indicator flashes rapidly to

indicate a charging problem. Reinsert the battery

pack or try a new one. If the new pack also

refuses to charge, have your charger tested by

an authorized DEWALT repair agent.

• When plugged into power sources such as

generators or sources that convert DC to AC,

the red charging indicator may blink twice, switch

OFF and repeat.

This indicates a temporary problem of the power

source. The charger will automatically switch

back to normal operation.

Inserting and removing the battery pack

• Insert the battery pack into the grip (8) until it

clicks in place.

• To remove the battery pack, press the two

release buttons (10) simultaneously and pull the

pack out of the grip (8).

Inserting and removing bits (fig. A & B)

Your drill is equipped with a bit holder (7).

• Open the chuck by turning the sleeve (13)

counterclockwise and insert the bit shank.

• Place the bit in the chuck as far as it will go and

lift slightly before tightening.

• Tighten firmly by turning the sleeve clockwise.

• To remove the bit, proceed in reverse order.

Selecting the operating mode or adjusting the

torque (fig. C)

The collar of this tool has 17 positions for the

adjustment of the torque to suit the size of the screw

and the workpiece material. For torque adjustment,

refer to the section «Screwdriving».

• Select the drilling mode or torque by aligning the

symbol or number on the collar (5) with the

indicator (14) on the housing.

Forward/reverse switch (fig. D)

• To select forward or reverse rotation, use the

forward/reverse slider (2) as shown

(see arrows on tool).

Always wait until the motor has come to

a complete standstill before changing the

direction of rotation.

Two gear selector (fig. E)

Your tool is fitted with a two gear selector (6) to vary

the speed/torque ratio.

1 low speed/high torque

(drilling large holes, driving screws)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt dw 954 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info