Bedienungsanleitung DeWalt dw 956 2 (Seite 23 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

387208

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

Description (fig. A)

Your cordless drill/driver DW927/DW928/DW929/

DW956/DW957 has been designed for professional

drilling and screwdriving applications.

1 Variable speed switch

2 Forward/reverse slider

3 Two gear selector

4 Mode selector/torque adjustment collar

5 Collar settings

6 Keyless chuck

7 Bit holder

8 Grip

9 Battery pack

Charger

Your DE9107 charger accepts DEWALT NiCd

battery packs ranging from 7.2 V to 14.4 V.

Your DE9108/DE9118 charger accepts DEWALT

NiCd battery packs ranging from 7.2 V to 18 V.

Your DE9116 charger accepts DEWALT NiCd and

NiMH battery packs ranging from 7.2 V to 18 V.

9 Battery pack

10 Release buttons

11 Charger

12 Charging indicator (red)

Electrical safety

The electric motor has been designed for one

voltage only. Always check that the battery pack

voltage corresponds to the voltage on the rating

plate. Also make sure that the voltage of your

charger corresponds to that of your mains.

Your DEWALT charger is double

insulated in accordance with EN 60335.

Mains plug replacement

(U.K. & Ireland only)

• Should your mains plug need replacing and you

are competent to do this, proceed as instructed

below. If you are in doubt, contact an authorized

DEWALT repair agent or a qualified electrician.

• Disconnect the plug from the supply.

• Cut off the plug and dispose of it safely; a plug

with bared copper conductors is dangerous if

engaged in a live socket outlet.

• Only fit 13 Amperes BS1363A approved plugs

fitted with the correctly rated fuse (1).

• The cable wire colours, or a letter, will be marked

at the connection points of most good quality

plugs. Attach the wires to their respective points

in the plug (see below). Brown is for Live (L) (2)

and Blue is for Neutral (N) (4).

• Before replacing the top cover of the mains plug

ensure that the cable restraint (3) is holding the

outer sheath of the cable firmly and that the two

leads are correctly fixed at the terminal screws.

Never use a light socket.

Never connect the live (L) or neutral (N)

wires to the earth pin marked E or .

Using an extension cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of your charger

(see technical data). The minimum conductor size is

1 mm

; the maximum length is 30 m.

Assembly and adjustment

• Prior to assembly and adjustment,

always remove the battery pack.

• Always switch off the tool before

inserting or removing the battery pack.

• Use only DEWALT battery packs and

chargers.

Battery pack (fig. A)

Charging the battery pack

• To charge the battery pack (9), insert it into the

charger (11) as shown and plug in the charger.

Be sure that the battery pack is fully seated in the

charger, but do not force it.

The red charging indicator (12) will blink. After

approx. 1 hour, it will stop blinking and remain on.

The battery pack is now fully charged and the

charger automatically switches to equalisation mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt dw 956 2 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info