Bedienungsanleitung DeWalt dw 988 xrp k2 (Seite 25 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388592

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

21 en - 6

Selecting the operating mode or adjusting the

torque (fig. C)

The collar of this tool has a wide range of positions

for the adjustment of the torque to suit the size of

the screw and the workpiece material. For torque

adjustment, refer to the section «Screwdriving».

• Select the drilling mode or torque by aligning the

symbol or number on the collar (4) with the

indicator (16) on the housing.

DW981/DW984/DW985/DW988/DW989

The percussion drills can be used in the following

operating modes:

Rotary drilling:

for steel, wood and plastics

Percussion drilling:

for masonry

Forward/reverse slider (fig. D)

• To select forward or reverse rotation, use the

forward/reverse slider (2) as shown (see arrows

on tool).

Always wait until the motor has come to

a complete standstill before changing the

direction of rotation.

Three-gear selector (fig. E)

Your tool is fitted with a three-gear selector (6) to

vary the speed/torque ratio.

1 low speed/high torque

2 medium speed/medium torque

3 high speed/low torque

For speed rates, refer to the technical data.

Do not change gears at full speed or

during use.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool.

Switching on and off (fig. A & D)

• To run the tool, press the variable speed switch

(1). The pressure exerted on the variable speed

switch determines the tool speed.

• To stop the tool, release the switch.

• To lock the tool in the off position, move the

forward/reverse slider (2) to the central position.

Screwdriving (fig. A)

• Select forward or reverse rotation using the slider (2).

• Set the collar (4) to position 1 and begin

screwdriving (low torque).

• If the clutch ratchets too soon, adjust the collar

to increase the torque as required.

Drilling (fig. A)

• Select the drilling mode using the collar (4).

• Select forward rotation.

Drilling in metal

• Use a cutting lubricant when drilling metals.

The exceptions are cast iron and brass which

should be drilled dry.

Drilling in wood

• Use the appropriate type of drill bit.

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT Power Tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

• Unplug the charger before cleaning the housing

with a soft cloth.

• Remove the battery pack before cleaning your

power tool.

DW980_989.P65 14-09-2001, 08:3725

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt dw 988 xrp k2 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info