Bedienungsanleitung DeWalt dw 996 k (Seite 28 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

387229

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Removing and fitting the chuck (fig. E & F)

• Open the chuck jaws as far as possible.

• Tighten an Allen key (14) into the chuck and

strike it with a hammer as shown in figure E.

• Insert a screwdriver into the chuck and remove

the chuck retaining screw by turning clockwise.

• Tighten an Allen key (14) into the chuck and

strike it with a hammer as shown in figure F.

This will loosen the chuck so that it can be

unscrewed by hand.

• To refit the chuck, proceed in reverse order.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework

and wiring.

• Apply only a gentle pressure to the tool.

Excessive force does not speed up

drilling but decreases tool performance

and may shorten tool life.

Prior to operation:

• Insert the appropriate bit.

• Mark the spot where the hole is to be drilled.

• Make sure your battery pack is (fully) charged.

• Select forward or reverse rotation.

Switching ON and OFF (fig. A)

• To run the tool, press the variable speed switch

(1). The pressure exerted on the variable speed

switch determines the tool speed.

• To stop the tool, release the variable speed

switch (1).

• To lock the tool in OFF-position, move the

forward/reverse slider (2) to the central position.

Screwdriving (fig. C & D)

• Select forward or reverse rotation using the

slider (2).

• Use the low speed/high torque position

(1st gear) (3).

• Set the torque adjustment collar (4) (DW976 &

DW996). The higher the number on the collar,

the higher the torque and the larger the fastener

which can be driven.

DW976 & DW996 - Percussion Drilling (fig. C)

• Select the percussion mode.

• Press the variable speed switch (1).

• To stop the tool, release the switch.

All models - Drilling (fig. C)

• Select the drilling mode (DW976, DW996).

• Proceed as described for percussion drilling.

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT Power Tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Lubrication

Your Power Tool requires no additional lubrication.

Cleaning

• Unplug the charger before cleaning the housing

with a soft cloth.

• Remove the battery pack before cleaning your

Power Tool.

• Keep the ventilation slots clear and regularly

clean the housing with a soft cloth.

Environment

Rechargeable battery pack

This long life battery pack must be recharged when

it fails to produce sufficient power on jobs which

were easily done before. At the end of its technical

life, discard it with due care for our environment:

• Run the battery pack down completely, then

remove it from the tool.

• NiCd cells are recyclable. Take them to your

dealer or a local recycling station. The collected

battery packs will be recycled or disposed of

properly.

ENGLISH

en - 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt dw 996 k Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info