Bedienungsanleitung DeWalt DW074 (Seite 32 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

790945

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

ENGLISH

TURNING THE LASER OFF

Gently press the power button (e) to turn the laser

off. The power LED indicator light (g) will no longer

be illuminated.

Laser Control Panel Buttons (ﬁ g. 1)

POWER BUTTON

Press the power button (e) to power the unit on and

off.

ARROW BUTTONS

The arrow buttons (j, k) are used to adjust/level the

bubble in the vial. The single arrow buttons move

the bubble slowly; the double arrow buttons allow

fast adjustment of the bubble.

SPEED/ROTATION BUTTON

The speed/rotation button (h) is used to adjust the

rotation speed of the laser beam through its 3 preset

speeds.

The head speed will cycle through 3 speeds, then

repeat the sequence as the speed/rotation button is

pressed.

REMEMBER:

Slow speed = Bright Beam

Fast Speed = Solid Beam

STANDBY BUTTON

Press the standby button (i) to engage Standby

Mode. This turns off the laser beam and stops the

laser head from rotating. The standby LED indicator

light (f) will flash when the unit is in Standby Mode.

NOTE: Pressing any of the arrow buttons (j, k) will

also engage Standby Mode.

CAUTION: To reduce the risk of direct

eye exposure to the laser beam, always

engage Standby Mode before viewing

the bubble vial.

LOW BATTERY INDICATION

When the batteries approach end of life, the power

LED indicator light (g) will begin to flash. When this

signal is observed, only a short period of runtime is

left before the unit will completely shut down. The

batteries should be replaced with new batteries as

soon as possible.

Laser Accessories

LASER EN HANCEMENT GLASSES (FIG. 6)

These red lens glasses improve the visibility of the

laser beam under bright light conditions or over

long distances when the laser is used for interior

applications. These glasses are not required to

operate the laser.

DANGER: To reduce the risk of serious

personal injury, never stare directly into

the laser beam, with or without these

glasses.

CAUTION: These glasses are not

approved safety glasses and should

not be worn while operating other tools.

These glasses do not keep the laser

beam from entering your eyes.

TARGET CARD (FIG. 7)

The Laser Target Card aids in locating and marking

the laser beam. The target card enhances the

visibility of the laser beam as the beam crosses over

the card. The card is marked with standard and

metric scales. The laser beam passes through the

red plastic and reflects off of the reflective tape on

the reverse side. The magnet at the top of the card

is designed to hold the target card to ceiling track or

steel studs to determine plumb and level positions.

For best performance when using the Target Card,

the DEWALT logo should be facing you.

DIGITAL LASER DETECTOR (FIG. 8)

The detector helps in locating the position of a

laser beam in bright light conditions or over long

distances. It produces both visual and audio signals

as the rotating laser beam crosses the detector.

The detector can be used both indoor and outdoor

whenever it is difficult to locate the laser beam.

The detector is not for use with non-rotating lasers

but is compatible with most rotary red-beam or

infrared (invisible) beam lasers on the market.

The DEWALT Digital Laser Detector can be used

with or without the detector clamp. When used

with the clamp, the detector can be positioned on a

grade rod, leveling pole, stud or post.

Accuracy

When the laser is operated using the detector, the

accuracy level of the detector needs to be added to

that of the laser.

• Nominal accuracy ± 3.0 mm

Mounting Detector on a Grade Rod (fig. 8)

1. To secure your detector to a grade rod, first

attach the detector to the clamp by pushing in

on the clamp latch (w). Slide the tracks (x) on

the clamp around the rail (y) on the detector

until the latch (z) on the clamp pops into the

latch hole (aa) on the detector.

2. Open the jaws of the clamp by turning the

clamp knob (bb) counterclockwise.

3. Position the detector at the height needed and

turn the clamp knob clockwise to secure the

clamp on the rod.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW074 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info