Bedienungsanleitung DeWalt DW153 (Seite 22 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

500484

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

en - 5 17

ENGLISH

The direction of rotation must only be

changed when the motor has come to a

complete standstill. A safety device

prevents any change of rotation if the

motor is still switched ON.

Two gear selector (fig. C)

The tool is fitted with a two gear selector (4) to vary

the speed/torque ratio.

• Release the ON/OFF-switch and select the

required position after the motor has come to a

complete standstill.

I low speed/high torque

(drilling large holes) (position I)

II high speed/low torque

(drilling smaller holes) (position II)

For speed rates, refer to the technical data.

Do not try to change gears at full speed

or under load.

Mounting the drill onto a drill stand (fig. D)

Your drill can be mounted on a drill stand (optional)

for stationary use.

• Remove the breast plate by loosening the fixing

bolt.

• Remove both side handles.

• Mount the tool onto the drill stand. Make sure to

tighten all fixing bolts provided with the drill stand.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Apply only a gentle pressure to the tool.

Excessive force decreases tool

performance and may shorten tool life.

Using the drill as a hand-held tool (fig. A)

• Fit the side handles and the breast plate.

• Insert the appropriate accessory.

• Select the direction of rotation.

• Select the appropriate speed/torque ratio.

• To run the tool, press the ON/OFF-switch (1) in

the control side handle (7).

• To stop the tool, release the ON/OFF-switch.

Always switch OFF the tool when work is finished

and before unplugging.

Stationary use (fig. A)

• Remove the side handles and the breast plate.

• Mount the tool onto a drill stand (shown in fig. D).

• Insert the appropriate accessory.

• Select the direction of rotation.

• Select the appropriate speed/torque ratio.

• To run the tool, press the ON/OFF-switch (1) in

the carrying handle (5).

• If necessary, press the lock-on button (2) for

continuous operation and release the ON/OFF-

switch. The lock-on button works both in forward

and reverse rotation.

• To stop the tool, release the ON/OFF-switch.

• To stop the tool in continuous operation, press the

ON/OFF-switch briefly.Always switch OFF the tool

when work is finished and before unplugging.

Mixing

• For mixing, fit an appropriate mixing accessory.

Do not mix or stir inflammable liquids

labelled accordingly.

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT Power Tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

• The heavy duty drill is not user-serviceable.

We recommend to take the tool to a DEWALT

authorized repair agent after approximately

150 hours of use.

Lubrication

Your Power Tool requires no additional lubrication.

Cleaning

Keep the ventilation slots clear and regularly clean

the housing with a soft cloth.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW153 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info