Bedienungsanleitung DeWalt DW302K (Seite 21 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

546577

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

• When the tool is used indoor for extended

periods of time, use a suitable dust extractor

designed in compliance with the applicable

directives regarding dust emission.

• Whenever possible, connect a dust extraction

device designed in accordance with the relevant

regulations regarding dust emission.

Cutting metal (fig. A)

• When cutting thin metal always stabilize the

workpiece with wood on both sides.

This guarantees clean cuts and prevents

damaging of the material.

• For long, straight cuts draw a line on the workpiece.

• Apply a thin film of lubricant along the cutting

line, switch on the tool and follow the cutting line.

Cutting plastics

• Always work at reduced speed. Carry out a test

cut to check whether the material is sensitive to

heat.

Cutting masonry

When sawing asbestos cement

hazardous dust may be produced.

Follow the statutory guidelines and

observe the recommendations issued by

the asbestos cement manufacturers.

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT Power Tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Lubrication

• If the tool will not be used for a long period of

time, coat the saw blade with a little oil

(e.g. machine oil).

17 en - 5

ENGLISH

• When sawing in walls or floors be aware

of the location of pipework and wiring.

Always hold the tool by its handle.

• Avoid overloading.

Prior to operation:

• Mount the appropriate type of saw blade.

Use narrow saw blades for cutting curves.

Use flexible bimetal saw blades for hard-to-reach

positions (e.g. close to walls, etc.).

Switching on and off (fig. A)

• To run the tool, press the variable speed switch (1).

The pressure exerted on the variable speed switch

determines the tool speed.

• Let the blade run freely for a few seconds before

starting the cut. Never switch on the tool when

the saw blade is jammed in the workpiece or in

contact with the material.

• Always switch off the tool before unplugging.

Cutting wood (fig. A)

• Clamp the workpiece securely and remove all

nails and metal objects.

• Holding the tool with both hands, work with the

saw shoe (6) pressed against the workpiece.

Plunge cutting in wood

• Rest the saw shoe (6) on the workpiece in such a

position that the blade forms an appropriate

angle for the plunge cut.

• Switch the tool on and slowly feed in the blade.

Make sure that the saw shoe remains in contact

with the workpiece at all times.

Pocket cuts

• Measure and mark the required pocket cut.

• Using a narrow saw blade rest the bottom of the

saw shoe (6) on the workpiece and make sure

that the blade is positioned on the cutting line.

If necessary, e.g. in confined spaces, use the

outer edge of the saw shoe as your guideline.

• Switch on the tool and feed the blade into the

material at full speed, holding the tool firmly

against the workpiece.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW302K Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info