Bedienungsanleitung DeWalt dw310k (Seite 27 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

382575

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

ENGLISH

Proper hand position requires one hand on the side

front grip (k), with the other hand on the back

handle (m).

Switching On and Off (ﬁ g. 1)

To run the tool, press the variable speed switch (a).

The pressure exerted on the variable speed switch

determines the tool speed.

To stop the tool, release the switch.

Always switch off the tool when work is finished and

before unplugging.

SETTING THE ELECTRONIC SAWING SPEED

(FIG. 1) - DW311

The speed control dial (b) can be used for advance

setting of the required range of speed.

Turn the electronic speed control dial to the required

level. The required setting depends on the thickness

and kind of material.

Use high speeds for sawing soft materials such as

wood. Use low speeds for sawing metal.

WARNING: After using the tool for

an extended period on low speed

settings, run it for approx. 3 minutes on

maximum no-load speed.

Cutting Wood

1. Clamp the workpiece securely and remove all

nails and metal objects.

2. Holding the tool with both hands, work with the

saw shoe pressed against the workpiece.

Plunge Cutting in Wood (ﬁ g. 5)

1. Rest the saw shoe on the workpiece in such

a position that the blade forms an appropriate

angle for the plunge cut.

2. Switch the tool on and slowly feed in the blade.

Make sure that the saw shoe remains in contact

with the workpiece at all times.

Pocket Cuts

1. Measure and mark the required pocket cut.

2. Using a narrow saw blade rest the bottom of

the saw shoe on the workpiece and make sure

that the blade is positioned on the cutting line.

If necessary, e.g. in confined spaces, use the

outer edge of the saw shoe as your guideline.

3. Switch on the tool and feed the blade into the

material at full speed, holding the tool firmly

against the workpiece.

Cutting Metal

When cutting thin metal always stabilize the

workpiece with wood on both sides. This guarantees

clean cuts and prevents damaging of the material.

For long, straight cuts draw a line on the workpiece.

Apply a thin film of lubricant along the cutting line,

switch on the tool and follow the cutting line.

Cutting Plastics

Always work at reduced speed. Carry out a test cut

to check whether the material is sensitive to heat.

Cutting Masonry

WARNING: When sawing asbestos

cement hazardous dust may be

produced. Follow the statutory

guidelines and observe the

recommendations issued by the

asbestos cement manufacturers.

Sawing Up to a Projecting Edge

(ﬁ g. 6)

Using a conventional blade installed upside down,

cut up to the projected edge.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing

set-ups or when making repairs.

Be sure the trigger switch is in the OFF

position. An accidental start-up can

cause injury.

Dust Extraction

When the tool is used indoor for extended periods

of time, use a suitable dust extractor designed in

compliance with the applicable Directives regarding

dust emission.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt dw310k Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info