Bedienungsanleitung DeWalt DW322 (Seite 27 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

447095

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

• Slide the selector (4) to the desired position

referring to the table below. The selector can be

manipulated during operation.

Pos. Wood Metal Plastics

3 Fast cuts - PVC

2 Thick workpieces - Fibreglass

Acrylic

1 Plywood Aluminium -

Chipboard Non-ferrous -

0 Thin workpieces Sheet metal -

Fine cuts

Optional accessories

Installing the parallel fence (fig. J)

• Install the parallel fence (19) as shown.

Installing the trammel bar (fig. K)

• Install the trammel bar (20) as shown.

• Secure the trammel bar in the centre of the hole

to be cut.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Make sure your workpiece is well

secured. Remove nails, screws and other

fasteners that may damage the blade.

• Check that there is sufficient space for

the blade underneath the workpiece.

Do not cut materials that are thicker than

the maximum cutting depth.

• Use sharp saw blades only. Damaged or

bent saw blades must be removed

immediately.

• Do not use the tool for sawing pipes

or tubes.

• Never run your tool without a saw blade.

• For optimal results, move the tool

smoothly and constantly over the

workpiece. Do not exert lateral pressure

on the saw blade. Keep the shoe flat on

the workpiece and lead the cord away in

line with the tool. When sawing curves,

circles or other round shapes, push the

tool gently forward.

• Wait until the tool has come to a

standstill before removing the saw blade

from the workpiece.

After sawing the blade may be very hot.

Do not touch.

Switching on and off (fig. A)

DW321/DW322

• Switching on: press the on/off-switch (1).

The sawing speed of the DW321 varies with the

pressure exerted on the on/off-switch (1).

• For continuous operation, press the lock-on

button (3).

• Switching off: press the on/off-switch once more.

Always switch the tool off when the work is

finished and before unplugging.

DW323/DW324

• Switching on: slide the on/off-switch (1) to the front.

• Switching off: slide the on/off-switch to the rear.

Always switch the tool off when the work is

finished and before unplugging.

Sawing in wood

• If necessary, draw a cutting line.

• Switch the tool on.

• Hold the tool against the workpiece and follow

the line.

• For sawing parallel to the edge of your

workpiece, install the parallel fence and guide

your jigsaw along the workpiece as shown in

figure J.

Sawing in wood using a pilot hole

• If necessary, draw a cutting line.

• Drill a hole (ø min. 12 mm) and introduce the saw

blade.

• Switch the tool on.

• Follow the line.

• For cutting perfectly round shapes, install the

trammel bar and set it to the required radius.

Sawing up to a projecting edge (fig. D)

• Remove the straight/round cut guide, if installed.

• Set the pendulum stroke selector to 0.

• Loosen the screw (14) using the Allen key (13).

• Push the shoe (6) all the way backward.

ENGLISH

21 en - 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW322 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info