Bedienungsanleitung DeWalt DW340K (Seite 22 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546438

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

en - 5 18

ENGLISH

Medium (2nd sector) • Welding plastics

• Bending plastic pipes and sheets

• Loosening rusted or tightly fastened nuts

and bolts

High (4th sector) • Removing paint and lacquer

• Soldering plumbing joints

• If you are not sure about the correct setting,

start with a low temperature setting and gradually

increase the temperature until you achieve

optimum results.

Mounting the correct accessory

This tool is supplied with a set of accessories for

different applications.

Icon Description Purpose

Glass protection nozzle Protecting windows when

stripping frames

Spoon reflector nozzle Soldering pipes

Cone nozzle Welding, shrink sleeving (heat

concentrated over small area)

Fish tail surface nozzle Drying, thawing

(heat spread over wider area)

Scraper Stripping paint and varnish

• Make sure that the tool is switched off and the

nozzle has cooled down.

• Set the desired accessory onto the nozzle.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Use only one hand to hold the tool

(fig. C). Do not place your other hand

over the air vents (fig. D).

Prior to operation:

• Mount the correct accessory for the application.

• Set the desired air temperature.

Switching on and off (fig. E)

• To switch the tool on, set the on/off switch to

position I. Some smoke may be emitted after

switching on; this does not indicate a problem.

• To switch the tool off, set the on/off switch to

position O. Let the tool cool down before moving

or storing it.

Stripping paint (fig. F)

• Mount an appropriate accessory.

• Set a high air temperature.

• Switch the tool on.

• Direct the hot air onto the paint to be removed.

• When the paint softens, scrape the paint away

using a hand scraper.

• Do not strip metal window frames, as the

heat may be conducted onto the glass

and crack it.

• When stripping other window frames,

use the glass protection nozzle.

• Do not keep the tool directed at one

spot too long to prevent igniting the

surface.

• Avoid collecting paint on the scraper

accessory, as it may ignite. If necessary,

carefully remove paint debris from the

scraper accessory using a knife.

Stationary use (fig. G)

This tool can also be used in stationary mode.

• Place the tool onto the workbench as shown.

• Secure the cable to prevent pulling the tool off

the workbench.

• Carefully switch the tool on.

• Make sure that the nozzle always points

away from you and any bystanders.

• Make sure not to drop anything into the

nozzle.

Cooling down

The nozzle and accessory become very hot during

use. Let them cool down before attempting to move

or store the tool.

• To reduce the cooling time, switch the tool on at

the lowest air temperature setting and let in run

for a few minutes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW340K Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info