Bedienungsanleitung DeWalt DW411 T 4 (Seite 62 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546675

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

en - 3

Check for misalignment and seizure of moving

parts, breakage of parts and any other conditions

that may affect its operation. Have damaged

guards or other defective parts repaired or

replaced as instructed. Do not use the tool if the

switch is defective. Have the switch replaced by

an authorized DeWALT repair agent.

20 Have your tool repaired by an authorized

DeWALT repair agent

This Power Tool is in accordance with the relevant

safety regulations. To avoid danger, electric

appliances must only be repaired by qualified

technicians.

Sanding paint

Observe the applicable regulations for sanding

paint. Pay special attention to the following:

1 Take special care when sanding paint which is

possibly lead based:

• Do not let children or pregnant women enter the

work area.

• All persons entering the work area should wear

a mask specially designed for protection against

lead paint dust and fumes.

• Do not eat, drink or smoke in the work area.

2 Dispose of dust particles and any other removal

debris safely.

Package contents

The package contains:

1 1/4 Sheet Sander

1 Hole perforation jig

1 Dustbag

1 Set of sanding sheets

1 Instruction manual

1 Exploded drawing

1 Registration card

• Check for damage to the tool, parts or

accessories which may have occurred during

transport.

• Take the time to thoroughly read and understand

this manual prior to operation.

Description (fig. A)

Your DeWALT 1/4 sander has been designed for

professional sanding of wood, woodwork and plastics.

1 ON/OFF-switch

2 Sanding sheet clamps

3 Sanding sheet clamp springs

4 Sanding pad

5 Dustbag adaptor

6 Dustbag

Electrical safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DeWALT tool is double insulated in

accordance with prEN 50144; therefore

no earth wire is required.

Mains plug replacement (U.K. & Ireland

only)

• Should your mains plug need replacing and you

are competent to do this, proceed as instructed

below. If you are in doubt, contact an authorized

DeWALT repair agent or a qualified electrician.

• Cut off the plug and dispose of it safely; a plug

with bared copper conductors is dangerous if

engaged in a live socket outlet.

• Only fit 13 Amperes BS1363A approved plugs

fitted with the correctly rated fuse (1).

• The cable wire colours, or a letter, will be marked

at the connection points of most good quality

plugs. Attach the wires to their respective points

in the plug (see below). Brown is for Live (L) (2)

and Blue is for Neutral (N) (4).

• Before replacing the top cover of the mains plug

ensure that the cable restraint (3) is holding the

outer sheath of the cable firmly and that the two

leads are correctly fixed at the terminal screws.

Never use a light socket.

Never connect the live (L) or neutral (N)

wires to the earth pin marked E or .

For 115 V tools, use plugs to BS4343 standard.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW411 T 4 Seite 62

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info