546186
21
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
16 en - 5
ENGLISH
If the sanding frame is not being used, the
locking shaft (13) can be rotated a quarter
of a turn. It is not necessary to remove the
locking shaft because the crankshaft will
park inside the recess (11).
Mounting and removing the stationary stand
(fig. A & F)
With a stationary stand (option), the machine can be
used in a stationary position both upside down and
horizontally.
If required, mount the sanding frame (14) as
described above.
Place the belt sander on the stationary stand (18).
Guide the cord away at the side of the clamping
lever (12).
Place the fixing bolt (19) and tighten the round
nut (20) (see inset in figure F).
To remove the stationary stand, proceed in
reverse order.
Dust extraction (fig. A)
Since woodworking with a sander
produces dust, always install a dustbag
designed in compliance with the
applicable directives regarding dust
emission.
Do not use a dustbag or vacuum
extractor without proper spark protection
when sanding metal.
Do not sand magnesium!
Place the dustbag (7) over the flange (21) or
connect a vacuum extractor.
For efficient dust extraction empty the dustbag
when it is about one third full.
Remove the dustbag from the flange, open the
zipper and gently shake out the dustbag.
Instructions for use
Always observe the safety instructions
and applicable regulations.
Make sure all materials to be sanded are
well secured.
Apply only a gentle pressure to the
workpiece.
Switching on and off (fig. A)
Switching on: press the on/off-switch (1).
For continuous operation, also press the lock-on
button (3).
Switching off: press the on/off-switch again.
Always switch off the tool when work is
finished and before unplugging.
Consult your dealer for further information on the
appropriate accessories.
Maintenance
Your DEWALT Power Tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
Keep the ventilation slots clear and regularly clean
the housing with a soft cloth.
Unwanted tools and the environment
Take your tool to an authorized DEWALT repair
agent where it will be disposed of in an
environmentally safe way.
21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für DeWalt DW431 T 5 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info