Bedienungsanleitung DeWalt DW491K T 1 (Seite 22 von 79) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

548704

Zoom out

Zoom in

Vorherige Seite

1/79

Nächste Seite

Fitting and removing a grinding wheel or cutting

disk (fig. D)

• Place the tool on a table, guard up.

• Fit the spacer (20) correctly onto the spindle (5).

• Place the grinding wheel or cutting disk on the

spacer.

• Screw the threaded flange (21) onto the spindle (5).

• Press the spindle lock (4) and rotate the grinding

wheel or cutting disk until it locks in position.

• Tighten the threaded flange (21) with the two-pin

spanner supplied.

• Release the spindle lock.

• To remove the grinding wheel or cutting disk, loosen

the threaded flange (21) with the two-pin spanner.

Fitting a wire cup brush

• Screw the wire cup brush directly onto the

spindle without the use of the spacer and

threaded flange.

Mounting the side handle (fig. E)

• For grinding, screw the side handle (6) tightly into

one of the holes (8) on either side of the gear case.

• For cutting, screw the side handle (6) tightly into

the top hole (7).

DW491K - Mounting the round handle (fig. F)

• Remove the side handle.

• Mount the round handle (22) using the two

screws (23).

• Fit one screw in the top hole (7) and the other in

one of the side holes (8).

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Ensure all materials to be ground or cut

are secured in place.

• Apply only a gentle pressure to the tool.

Do not exert side pressure on the

grinding wheel or cutting disk.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

Prior to operation:

• Install the appropriate guard and disk or wheel.

Do not use excessively worn disks or wheels.

• Be sure the spacer and threaded flange are

mounted correctly.

• Make sure the disk or wheel rotates in the direction

of the arrows on the accessory and the tool.

Switching ON and OFF (fig. A)

The ON/OFF-switch of your Angle Grinder is

equipped with an unlocking switch or a locking switch

for continuous operation.

(U.K. & France only) - ON/OFF-switch (1) with

unlocking switch (2)

• To unlock the ON/OFF-switch, slide the unlocking

switch towards you.

• To run the tool, press the ON/OFF-switch.

• To stop the tool, release the ON/OFF-switch.

ON/OFF-switch (1) with locking switch (2a)

• To run the tool, press the ON/OFF-switch. The

tool now runs in continuous operation.

• To stop the tool, press the locking switch briefly,

and release the ON/OFF-switch.

Do not switch the tool ON or OFF when

under load.

DW491K - Using the Diamond guard (EZWS97)

(fig. C)

The Diamond guard is used for cutting concrete and

masonry, when accurate cutting depth adjustment or

dust extraction are required.

• Mount the Diamond guard as described above.

• Connect a dust extractor to the outlet (17).

• Set the cutting depth using the ruler knob in the

front plate (13).

• Observe the safety instructions applying

to diamond cutting disks.

• Use a suitable diamond cutting disk

(check the data of the manufacturer).

• The maximum rotation speed on the cutting

disk must not be lower than that of the tool.

• Do not use cutting disks with a diameter

exceeding 230 mm.

• Fire hazard! Do not use the dust

extractor when cutting metal!

• Make sure that the dust extractor used is

suitable for the material to be cut and the

Diamond guard can be connected.

en - 5

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW491K T 1 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info