Bedienungsanleitung DeWalt DW499 T 2 (Seite 23 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

548690

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

Description (fig. A)

Your DEWALT angle grinder DW476/DW479/

DW490/DW492/DW491/DW852/DW495/DW496/

DW497/DW498/DW499 has been designed for

professional grinding and cutting applications.

1 On/off-switch

2 Unlocking switch (U.K. & France only)

2a Locking switch

3 Guard

4 Spindle lock

5 Spindle

6 Side handle

7 Top hole

8 Side holes

9 Carbon brush covers

DW491/DW492/DW495/DW496/DW497/DW498/

DW499 - Soft start feature

The soft start feature allows a slow speed build-up

to avoid an initial jerk when starting. This feature is

particularly useful when working in confined spaces.

Electrical safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 50144; therefore no

earth wire is required.

Mains plug replacement

(U.K. & Ireland only)

• Should your mains plug need replacing and you

are competent to do this, proceed as instructed

below. If you are in doubt, contact an authorized

DEWALT repair agent or a qualified electrician.

• Disconnect the plug from the supply.

• Cut off the plug and dispose of it safely; a plug

with bared copper conductors is dangerous if

engaged in a live socket outlet.

• Only fit 13 Amperes BS1363A approved plugs

fitted with the correctly rated fuse (1).

• The cable wire colours, or a letter, will be marked

at the connection points of most good quality

plugs. Attach the wires to their respective points

in the plug (see below). Brown is for Live (L) (2)

and Blue is for Neutral (N) (4).

• Before replacing the top cover of the mains plug

ensure that the cable restraint (3) is holding the

outer sheath of the cable firmly and that the two

leads are correctly fixed at the terminal screws.

Never use a light socket.

Never connect the live (L) or neutral (N)

wires to the earth pin marked E or .

Fitting a mains plug to 115 V units

(U.K. & Ireland only)

• The plug should be fitted by a competent person.

If you are in doubt, contact an authorized

DEWALT repair agent or a qualified electrician.

The wires are coloured according to the following

code:

live = brown

neutral = blue

• Do not connect the blue or brown wire to the

earth terminal in the plug.

Connect as follows:

- brown to terminal marked ‘L’

- blue to terminal marked ‘N’

The plug fitted should be comply with BS EN 60309

(BS4343), 32 Amps.

Always ensure that the cable clamp is

correctly and securely fitted to the

sheath of the cable.

Using an extension cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

tool (see technical data). The minimum conductor

size is 1.5 mm2.

When using a cable reel, always unwind the cable

completely. Also refer to the table below.

DWLAG.P65 17-09-2001, 08:4923

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW499 T 2 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info