Bedienungsanleitung DeWalt DW516 T 3 (Seite 23 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544693

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

en - 5

Two gear selector (fig. C)

Your tool is fitted with a two gear selector to vary the

speed/torque ratio.

• Release the switch (1) and select the required

position. This can be done either with the tool

switched OFF or running under no load

condition. Always align the selector with the

arrow on the gear housing:

1 low speed/high torque(drilling large holes,

driving large screws)

2 high speed/low torque (drilling smaller holes,

drilling in wood)

For speed rates, refer to the technical data.

Do not change gears at full speed or

during use.

Chuck removal

Keyed chuck (fig. D)

• Insert the chuck key (8) into one of the holes in

the side of the chuck and strike it with a hammer

as shown.

Keyless chuck (fig. E)

• Open the chuck jaws as far as possible.

• Tighten an Allen key (9) into the chuck and strike

it with a hammer as shown.

Instructions for use

Always observe the safety instructions

and applicable regulations.

Prior to operation:

• Insert the appropriate bit.

• Mark the spot where the hole is to be drilled.

• Be aware of the location of pipework and wiring.

• Apply only a gentle pressure to the tool.

Excessive force does not speed up drilling but

decreases tool performance and may shorten

tool life.

Switching ON and OFF (fig. A)

• To run the tool, press the variable speed switch.

The pressure exerted on the variable speed

switch determines the tool speed.

• To stop the tool, release the switch.

Rotary drilling

• Select the appropriate speed.

• Proceed as described above.

Mixing

• For mixing, fit an appropriate mixing accessory

(not supplied with the tool).

• Do not use this tool to mix or pump

easily combustible or explosive fluids

(benzine, alcohol, etc.).

• Do not mix or stir inflammable liquids

labelled accordingly.

General tips for drilling with diamond core bits

Follow the core bit or manufacturer’s

recommendations for using the

accessory.

• Always use core bits with integral centre drill

systems.

• Insert the centredrill into its holder in the centre of

the core bit.

• Drill at low speed until the core penetrates the

surface approx. 5-10 mm.

• Remove and unplug the machine.

• Remove the centredrill from its holder.

• Plug the machine in and insert the core bit into

the workpiece.

• Begin drilling, increasing to full speed and drill to

the desired depth.

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT Power Tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Lubrication

Your Power Tool requires no additional lubrication.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW516 T 3 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info