Bedienungsanleitung DeWalt DW518 T 2 (Seite 29 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

544723

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

ENGLISH

Forward/reverse Slider (ﬁ g. 4)

To select forward or reverse rotation, use the

forward/reverse-switch (c) (see arrow on tool).

WARNING: Always wait until the motor

has come to a complete standstill

before changing the direction of

rotation.

Two-gear Selector (ﬁ g. 5)

Your tool is fitted with a two gear selector (d) to vary

the speed/torque ratio.

Release the variable speed switch and select the

required position. This can be done either with the

tool switched off or running under no load condition.

Always align the selector with the arrow on the gear

housing:

1 low speed/high torque (drilling large holes,

driving large screws)

2 high speed/low torque (drilling smaller holes,

drilling in wood)

For speed rates, refer to the technical data.

Do not change gears at full speed or during use.

Chuck Removal (ﬁ g. 6, 7)

KEYED CHUCK

1. Open the chuck jaws as far as possible.

2. Insert a screwdriver into the chuck and remove

the chuck retaining screw (m) by turning

clockwise as shown.

3. Insert the chuck key (j) into one of the holes in the

side of the chuck and strike it with a hammer as

shown.

4. Hold the spindle with a spanner if necessary.

KEYLESS CHUCK

1. Open the chuck jaws as far as possible.

2. Insert a screwdriver into the chuck and remove

the chuck retaining screw (m) by turning

clockwise.

3. Tighten an hex key into the chuck and strike it

with a hammer as shown.

Prior to Operation

1. Insert the appropriate bit.

2. Mark the spot where the hole is to be drilled.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

Proper Hand Position (ﬁ g. 1, 8)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the side

handle (f), with the other hand on the main handle

(k).

Switching On and Off (ﬁ g. 1)

T o run the tool, press the variable speed switch (a).

The pressure exerted on the variable speed switch

determines the tool speed.

Screwdriving

Select forward or reverse rotation.

Percussion Drilling (ﬁ g. 1)

1. Select the percussion mode.

2. Press the switch (a).

If necessary, press the lock-on slide (b) upwards

for continuous operation and release the switch.

The lock-on slide works only in full speed, forward

rotation.

To stop the tool, release the switch.

To stop the tool in continuous operation, press the

switch briefly and release it. Always switch off the

tool when work is finished and before unplugging.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW518 T 2 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info