Bedienungsanleitung DeWalt DW614 T 4 (Seite 30 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546404

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

Proper Hand Position (ﬁ g. A, H)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on each of

the plunge limiters (4).

Switching On and Off (ﬁ g. A)

Switch the tool on using the on/off-switch (1).

I = on. The tool now works continuously.

O = off.

WARNING: Loosen the plunge limiter

and allow the router carriage to regain

its rest position before switching off.

Using the Guide Bushes (ﬁ g. F)

1. Secure the template to the workpiece using end

clamps.

2. Select and install an appropriate guide

bush (18).

3. Subtract the diameter of the cutter from the

outside diameter of the guide bush and divide by

2. This will indicate how much larger the template

should be in relation to the part being recessed.

WARNING: If the workpiece is not thick

enough, place it on a piece of waste

wood.

Guiding Off a Batten

Where an edge guide cannot be used, it is also

possible to guide the router along a batten clamped

across the workpiece (with an overhang at both ends).

Freehand Routing

Your router can also be used without any sort of

guide, e.g. for signwriting or creative work.

WARNING: Make shallow cuts only!

Use cutters with a max. diameter of

6mm.

Routing with Pilot Cutters (ﬁ g. B)

Where a parallel guide or guide bush are

inappropriate, it is possible to use pilot cutters (20)

for cutting shaped edges.

Consult your dealer for further information on the

appropriate accessories.

Adjusting the Parallel Fence (ﬁ g. E)

1. Draw a cutting line on the material.

2. Lower the router carriage until the cutter is in

contact with the workpiece.

3. Tighten the plunge limiter (4).

4. Position the router on the cutting line. The outer

cutting edge of the cutter must coincide with

the cutting line.

5. Slide the parallel fence (16) against the

workpiece and tighten the locking bolts (17).

Fitting a Guide Bush (ﬁ g. F)

Together with a template, guide bushes play a

valuable part in cutting and shaping to a pattern.

1. Fit the guide bush (18) to the router base (11)

using the screws (19) as shown.

WARNING:The screws (19) also hold

the dust extraction channel. Never

operate the router without this.

Connecting a Dust Extractor (ﬁ g. A)

Connect a dust extractor hose to the dust extraction

channel (9).

Prior to Operation

1. Check that the cutter is correctly installed in the

collet.

2. Set the cutting depth.

3. Connect a dust extractor.

4. Always make sure the plunge limiter is locked

before switching ON.

OPERATION

Instructions for use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

WARNING: Always move your router

as indicated in fig. G (outer edges/inner

edges).

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW614 T 4 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info