Bedienungsanleitung DeWalt DW6141 (Seite 23 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546405

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

• Fit the guide bush (18) to the router base (11)

using the screws (19) as shown.

The screws (19) also hold the dust

extraction channel. Never operate the

router without this.

Connecting a dust extractor (fig. A)

Connect a dust extractor hose to the

dust extraction channel (9).

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Always move your router as indicated in

fig. G (outer edges/inner edges).

Prior to operation:

• Check that the cutter is correctly installed in the

collet.

• Set the cutting depth.

• Connect a dust extractor.

• Always make sure the plunge limiter is locked

before switching ON.

Switching on and off (fig. A)

Switch the tool on using the on/off-switch (1).

• I = on. The tool now works continuously.

• O = off.

Loosen the plunge limiter and allow the

router carriage to regain its rest position

before switching off.

Using the guide bushes (fig. F)

• Secure the template to the workpiece using end

clamps.

• Select and install an appropriate guide bush (18).

• Subtract the diameter of the cutter from the outside

diameter of the guide bush and divide by 2. This will

indicate how much larger the template should be in

relation to the part being recessed.

If the workpiece is not thick enough,

place it on a piece of waste wood.

18 en - 5

ENGLISH

• Lower the router carriage until the cutter is in

contact with the workpiece.

• Tighten the plunge limiter (4).

• Set the exact depth of cut using the graduation (2)

or place a depth template between the depth stop

(3) and the revolver depth stop (6). The adjustment

range is indicated by the arrows (14).

• Tighten the depth stop locking bolt (5).

Triple depth adjustment

The revolver depth stop (6) can be used to set three

different depths. This is particularly useful for deep

cuts, performed in steps.

• Place a depth template between the depth stop (3)

and the revolver depth stop (6) to adjust the exact

cutting depth.

• If required, set all three screws.

Depth adjustment with router installed in inverted

position

• Set the depth of cut prior to installing the router

in inverted position.

For installing the router in inverted

position, refer to the relevant instruction

manual on the stationary tool.

A fine depth adjuster (DE6956) is

available as an accessory.

Fitting the parallel fence (fig. A & E)

• Fit the guide rods (15) to the router base (11).

• Tighten the locking bolts (10).

• Slide the parallel fence (16) over the rods.

• Tighten the locking bolts (17) temporarily.

Adjusting the parallel fence (fig. E)

• Draw a cutting line on the material.

• Lower the router carriage until the cutter is in

contact with the workpiece.

• Tighten the plunge limiter (4).

• Position the router on the cutting line. The outer

cutting edge of the cutter must coincide with the

cutting line.

• Slide the parallel fence (16) against the workpiece

and tighten the locking bolts (17).

Fitting a guide bush (fig. F)

Together with a template, guide bushes play a

valuable part in cutting and shaping to a pattern.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW6141 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info