546203
26
Zoom out
Zoom in
Vorherige Seite
1/88
Nächste Seite
18
ENGLISH
en - 5
Tighten the locking screw (16).
Removing
To remove the parallel fence proceed in reverse
order.
Bevel adjustment (fig. C)
The bevel angle can be adjusted between 0° and 45°.
Slacken the locking screw (15).
Set the bevel angle by tilting the saw shoe (11).
The angle can be read on the bevel scale (14).
Tighten the locking screw (15).
Removing and installing the saw blade (fig. D)
Unplug the tool before proceeding.
Open the blade guard (8).
Rotate the saw blade until a screwdriver can be
inserted into the hole in the blade. This will
prevent the blade from rotating while being
loosened.
If no screwdriver is available, or if the saw blade
used does not have a hole, lock the blade by
pressing the teeth into a piece of wood.
Loosen and remove the blade bolt (9) and the
washer (23) using the wrench supplied.
Replace the saw blade. The teeth must point in
the direction of rotation, which is shown by the
arrow on the upper guard housing.
Reinstall the washer and tighten the blade bolt (9).
Adjusting the riving knife (fig. E)
For the correct adjustment of the riving knife (10),
refer to the inset in figure E. Adjust the clearance of
the riving knife when the saw blade is changed or
whenever necessary.
Loosen the screw and adjust the clearance as
shown in the inset in fig. E.
Tighten the screw.
Instructions for use
Always observe the safety instructions
and applicable regulations.
Ensure the material to be sawn is
secured in place.
Apply only a gentle pressure to the tool
and do not exert side pressure on the
saw blade.
Avoid overloading.
Voltage Amperes Cable rating (Amperes)
115 0-2.0 66 66 610
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
220/240 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Depth of cut adjustment (fig. A)
Slacken the locking screw (3) and the depth of
cut adjustment (6).
Set the correct depth of cut. The adjustment can
be read on the scale (13).
Tighten the depth of cut adjustment and the
locking screw.
For optimal results, allow the saw blade
to protrude from the workpiece by about
3 mm (e.g. for sawing 19 mm thick
board, adjust the depth of cut to
22 mm).
Mounting, adjusting and removing the parallel
fence (fig. B)
The parallel fence (7) is used for cutting parallel to
the edge of the workpiece.
Mounting
Place the parallel fence (7) on the saw shoe (11).
Insert the bolt (20) into the hole (21).
Place the clamping bracket (22) over the bolt and
tighten the locking screw (16).
Adjusting
Slacken the locking screw (16) and set the
parallel fence (7) to the desired width. The
adjustment can be read on the scale (19).
26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für DeWalt DW62 T 3 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info