Bedienungsanleitung DeWalt DW650 T 6 (Seite 27 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

546190

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

ENGLISH

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

Using an Extension Cable

If an extension cable is required, use an approved

3–core extension cable suitable for the power

input of this tool (see technical data).The minimum

conductor size is 1.5 mm

; the maximum length is

30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

Replacing and Centring the Sanding

Belt (ﬁ g. 2, 3)

Your belt sander uses 100 x 570 mm sanding belts.

1. Place the tool on its side with the clamping lever

(l) upwards.

2. Pull the clamping lever (l) upwards and to the

right.

3. Remove the sanding belt (e).

4. Place a new sanding belt making sure that the

arrow on the inside of the sanding belt points in

the same direction as the arrow on the machine

when on the same side of the rollers.

5 Push the clamping lever back.

6. Switch the machine ON and turn the outer belt

centring knob (f) until the sanding belt is centred

on the roller (k).

WARNING: The sanding belt should

never project at the rear! The sanding

belt should be flush with the outer edge

of the sanding surface.

Setting the Electronic Speed Control

Dial (ﬁ g. 1)

DW650E

Turn the speed control dial (b) to the desired

position. The higher the number, the higher the

belt speed.

Dust Extraction

DUSTBAG (FIG. 4)

1. Squeeze the spring (m) of the dustbag (g) and

release it between the fixing rings (n).

2. For efficient dust extraction empty the dustbag

when it is about one third full.

3. Remove the dustbag, open the zipper and

gently shake out the dustbag.

DUST EXTRACTION ADAPTOR

(FIG. 5)

Screw the dust extraction adaptor (h) onto the

outlet (o).

Whenever possible, connect a dust extraction device

designed in accordance with the relevant regulations

regarding dust emission.

WARNING: Do not use a dustbag or

vacuum extractor without proper spark

protection when sanding metal.

WARNING:

• Do not sand magnesium!

• Do not rough sand pure metal

surfaces.

OPERATION

Instructions for Use

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

WARNING:

• Always observe the safety

instructions and applicable

regulations.

• Make sure all materials to be sanded

are well secured.

• Apply only a gentle pressure to the

workpiece.

Sanding (ﬁ g. 1)

A guiding handle (i) has been provided for optimum

tool control when using the Belt Sander without the

stationary stand.

1. Start with the coarsest grit size.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW650 T 6 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info