Bedienungsanleitung DeWalt DW678E T 2 (Seite 22 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546599

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

en - 5 17

ENGLISH

• Slide the cutter (22) out of its holder.

• Reverse the cutter or replace it.

Always replace both cutters.

• Slide the cutter into the holder. At the rabbeting

side (i.e. the side where the side guard is mounted),

the cutter must be flush with the planing shoe.

• Tighten the three bolts (21).

Fitting the shavings discharge cassette (fig. G)

Although this planer was primarily designed for right-

hand side shavings discharge, it can also be used

for left-hand side shavings discharge.

For right-hand side shavings discharge, the planer

can be used with or wothout the cassette.

The cassette must be used in combination with the

dust extraction adaptor when connecting a vacuum

extractor.

• Push the cassette with its head end (23) into the

right-hand side shavings discharge outlet (24)

until it clicks in place. Please note that the figure

shows the left-hand side of the tool.

For left-hand side shavings discharge, the cassette

must always be used.

When using left-hand side shavings

discharge, always use the dust

extraction adaptor and a vacuum

extractor as described below to prevent

clogging. See fig. G.

• Push the cassette with its head end (23) into the

left-hand side shavings discharge outlet (24) until

it clicks in place.

• Connect the adaptor (25) to a vacuum extractor.

• To remove the cassette, depress the head end (23)

and pull out the cassette.

Instructions for use

Always observe the safety instructions

and applicable regulations.

Prior to operation:

• Adjust the depth of cut.

• If necessary, fit and adjust the parallel fence.

• Attach the shavings discharge cassette.

Use sharp cutters only.

Switching ON and OFF (fig. A)

Your Planer is equipped with a safety switch to

prevent inadvertent operation.

• Switching ON: press the lock-off button (2) and

subsequently press the ON/OFF-switch (1).

• Release the lock-off button (2).

• Switching OFF: release the ON/OFF-switch (1).

Always switch OFF the tool when work is finished

and before unplugging.

Dust extraction

Since woodworking with a planer produces dust,

always install a dustbag or connect a vacuum

extractor designed in compliance with the applicable

Directives regarding dust emission.

Your planer is supplied with an adapter for

connecting a dustbag or a vacuum extractor.

The dustbag is standard for K-models and available

as an option for all other models.

• Attach the dustbag to the shavings discharge

cassette using the adaptor for right-hand side

ejection only.

• Alternatively, for either left-hand or right-hand

side ejection, connect the planer to a vacuum

cleaner using the adaptor (25).

When using left-hand side shavings

discharge, always connect the planer to

a suitable vacuum extractor to prevent

clogging.

Planing (fig. A)

• Switch the tool ON as described.

• Slowly move the Planer over the workpiece.

• The feed speed should not be too high,

especially when using the maximum

depth of cut and planing width.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW678E T 2 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info