Bedienungsanleitung DeWalt DW680 T 2 (Seite 24 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546601

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISH

Attaching and Removing the Parallel

Fence (ﬁ g. 1, 2, 4)

The parallel fence (l) is used for optimum tool control

on narrow workpieces.

1. Slacken the wing bolt (f).

2. Fit the parallel fence (l) in the hole (g) from either

side.

3. Tighten the wing bolt.

4. To remove the parallel fence, proceed in reverse

order.

Removing Reversible Cutters (ﬁ g. 5)

1. Loosen the three bolts (m) with the spanner (n)

supplied.

2. Flap the side guard (h) up.

3. Slide the cutter (o) out of its holder.

4. Reverse the cutter or replace it.

WARNING: Always replace both

cutters.

5. Slide the cutter into the holder. Make sure that

the cutter is flush with the planing shoe (p).

6. Tighten the three bolts (m).

Prior to Operation:

Adjust the depth of cut.

If necessary, fit and adjust the parallel fence.

WARNING: Use sharp cutters only.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

Proper Hand Position (ﬁ g. 6)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the main

handle (r), with the other hand on the front

handle (d).

Switching On And Off (ﬁ g. 1, 2)

Your planer is equipped with a safety switch to

prevent inadvertent operation.

1. Switching on: press the lock-off button (b) and

subsequently press the on/off switch (a).

2. Release the lock-off button (b).

3. Switching off: release the on/off switch (a).

Always switch off the tool when work is finished and

before unplugging.

Planing (ﬁ g. 1, 2)

1. Switch the tool on as described.

2. Slowly move the planer over the workpiece.

WARNING: The feed speed should

not be too high, especially when using

the maximum depth of cut and planing

width.

NOTE: Remember that several shallow cuts are

better than one deep cut.

3. Switch the tool off.

Your planer is equipped with a parking shoe (k).

After switching off the tool can be put down without

waiting for the cutters to come to a standstill.

Dust Extraction

Whenever possible, connect a dust extraction device

designed in accordance with the relevant regulations

regarding dust emission.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing

set-ups or when making repairs.

Be sure the trigger switch is in the OFF

position. An accidental start-up can

cause injury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW680 T 2 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info