Bedienungsanleitung DeWalt DW682K T 3 (Seite 21 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546682

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

13 en - 3

• The cable wire colours, or a letter, will be marked at the connection

points of most good quality plugs. Attach the wires to their respective

points in the plug (see below). Brown is for Live (L) (2) and Blue is for

Neutral (N) (4).

• Before replacing the top cover of the mains plug ensure that the cable

restraint (3) is holding the outer sheath of the cable firmly and that the

two leads are correctly fixed at the terminal screws.

Never use a light socket.

Never connect the live (L) or neutral (N) wires to the earth pin

marked E or .

For 115 V units with a power rating exceeding 1500 W, we recommend to

fit a plug to BS4343 standard.

Using an extension cable

If an extension cable is required, use an approved extension cable suitable

for the power input of this tool (see technical data). The minimum

conductor size is 1.5 mm

. When using a cable reel, always unwind the

cable completely. Also refer to the table below.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0 - 2.0 6 6 6 6 6 10

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment always unplug the tool.

Adjustable fence (fig. C1 & C2)

The adjustable fence (6) allows you to precisely set the point where the

slots for the biscuits are cut. To set the fence height:

• Slacken the locking knob (9).

• Set the height adjuster (4) as required. With the fence set to 90°,

the scale under the locking knob reads the distance between the

centre of cutter and the surface of the fence.

• Tighten the locking knob.

To set the fence angle:

• Slacken the star knob (11).

• Tilt the fence into the required angle.

• Tighten the star knob.

Jointer base markings

When working without the fence, for example when making T-joints, you

can use the markings on the jointer base for proper alignment of the tool.

• Set the fence to the 0° position as described above.

• For workpieces with a thickness of 19 mm, use the edge of the base

as a reference for centring.

• For other workpieces, use the red centreline markings to align the tool.

• Two of the markings indicate the length of the cut. In order to prevent

breaking through the workpiece, make sure that the workpiece extends

beyond these markings.

Plunge depth adjustment (fig. D)

The plunge depth must be set to match the biscuit size. The numbers 0,

10 and 20 on the depth adjusting knob correspond with the biscuit size.

The M represents the maximum cutting depth of approx. 22 mm.

• Turn the depth adjusting knob (8) into the required position, aligning the

appropriate number with the red marking on the tool.

Plunge depth fine adjustment (fig. E)

The fine adjustment is used to eliminate possible tolerances in the size of

the biscuit slots.

• Raise the fence (6) to its upper position as described above.

• Insert the Torx screwdriver as shown and adjust the plunge depth as

required by turning the screw (turn clockwise to decrease the plunge

depth).

• Check the setting by making a trial cut in a piece of scrap wood.

Anti-slipping pins (fig. F)

The anti-slipping pins (7) help to reduce the tendency of the biscuit jointer

to slide to the right when cutting. When working on visible parts of the

workpiece, you may want to retract them in order to avoid scratching.

• To retract the pins, rotate them slightly clockwise using a flat

screwdriver.

• To use the pins again, rotate them slightly counterclockwise.

Replacing the blade (fig. G, H & J)

• Remove the four Torx screws (12) from the base plate and take off the

cover.

• Depress the spindle lock (10) and remove the flange by turning it

counterclockwise.

• Change the blade.

• Tighten the flange securely by turning it clockwise while keeping the

spindle lock depressed.

• Mount the cover plate and tighten the Torx screws.

• Make sure that the teeth of the cutter point in

counterclockwise direction as shown (fig. H).

• After replacing the blade, always check the cutting depth and

adjust if necessary.

Dust extraction (fig. K1 & K2)

Using the appropriate adapter, you can connect either a dustbag or a dust

extractor.

Dust extractor

• Insert the appropriate adapter (13) or (14) into the dust extraction outlet (5).

• Connect the dust extractor hose to the adapter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW682K T 3 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DW682K T 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info