Bedienungsanleitung DeWalt DW705 T 2 (Seite 26 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544975

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

en - 3 20

ENGLISH

• Press down the operating handle (1) and pull out the lock down pin (28),

as shown in fig. A2.

• Gently release the downward pressure and allow the arm to rise to its

full height.

Description (fig. B1 - B3)

1 Operating handle

2 Moveable lower guard

3 Fence right-hand side

4 Mitre clamp knob

5 Mitre latch

6 Mitre scale

7 Fence left-hand side

8 Bench mounting holes

9 Carrying handle

10 Head lock up release lever

11 Rear lower guard

12 Bevel scale (DW705 only)

13 Padlock hole

14 Motor housing

15 Spindle lock button

16 Brush inspection cap

17 Trigger switch

18 Blade spanner

19 Angle position stop (DW705 only)

20 Dust spout

21 Bevel clamp handle (DW705 only)

22 Hand indentation

23 Upper fence left-hand side clamping knobs (DW705 only)

24 Upper guard

25 Vertical position adjustment stop (DW705 only)

26 Bevel position adjustment stop (DW705 only)

27 Kerf plate

28 Head lock down pin

29 Work support extension

30 Adjustable length stop

31 Work piece clamp

32 Dustbag

Assembly

Prior to assembly always unplug the tool.

The motor and guards are already assembled onto the base.

Bench Mounting (fig. C1 & C2)

• Holes (8) are provided in all four feet to facilitate bench mounting.

Two different sized holes are provided to accommodate different sizes

of bolts (33). Use either hole; it is not necessary to use both.

Always mount your saw firmly to prevent movement. To enhance the

portability, the tool can be mounted to a piece of 12.5 mm or thicker

plywood which can then be clamped to your work support or moved to

other job sites and reclamped.

• When mounting your saw to a piece of plywood, make sure that the

mounting screws do not protrude from the bottom of the wood.

The plywood must sit flush on the work support. When clamping the

saw to any work surface, clamp only on the clamping bosses where

the mounting screw holes are located. Clamping at any other point will

interfere with the proper operation of the saw.

• Cut off the plug and dispose of it safely; a plug with bared copper

conductors is dangerous if engaged in a live socket outlet.

• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly

rated fuse (1).

• The cable wire colours, or a letter, will be marked at the connection

points of most good quality plugs. Attach the wires to their respective

points in the plug (see below). Brown is for Live (L) (2) and Blue is for

Neutral (N) (4).

• Before replacing the top cover of the mains plug ensure that the cable

restraint (3) is holding the outer sheath of the cable firmly and that the

two leads are correctly fixed at the terminal screws.

Never use a light socket.

Never connect the live (L) or neutral (N) wires to the earth pin

marked E or .

For 115 V tools, use plugs to BS4343 standard.

Using an extension cable

If an extension cable is required, use an approved triple-core extension

cable suitable for the power input of this tool (see technical data).

The minimum conductor size is 1.5 mm

When using a cable reel, always unwind the cable completely.

Also refer to the table below.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0-2.0 66 66610

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0-2.0 66 6666

2.1-3.4 66 6666

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Unpacking (fig. A1 & A2)

Remove the saw from the packing material carefully using the carrying

handle (9).

The package contains:

1 Assembled Mitre Saw

1 Blade spanner

1 305 mm TCT saw blade

2 Clamps (DW704 only)

1 Instruction manual

1 Exploded drawing

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW705 T 2 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info