english
22
– Risk of accidents caused by the uncovered parts of the rotating saw
blade.
– Risk of injury when changing the blade.
– Riskofsqueezingfingerswhenopeningtheguards.
– Healthhazardscausedbybreathingdustdevelopedwhensawing
wood,especiallyoak,beechandMDF.
The following factors are of influence to dust exposure:
~ worn saw blade
~ dust extractor with air velocity less than 20 m/s
~ workpiece not exactly guided
Markings on tool
The following pictograms are shown on the tool:
Read the instruction manual before use.
When using the machine in the mitre saw mode,
make sure that the upper part of the saw blade is
fully covered by the upper saw blade guard.
Only use the machine when the bench saw table is in
highest position.
When using the machine in the bench saw mode,
make sure that the upper and lower guards are in
place. Only use the machine when the bench saw
tableisinhorizontalposition.
Carrying point.
Package Contents
The package contains:
1 Assembled table top mitre saw
1 Parallel rip fence
1 Guard for bench saw position
1 Bottom guard for bench saw position
1 Push stick
1 Hex key 4/6 mm
1 Hex key 5 mm
1 Two-pin spanner
1 Dust extraction adapter for top guard
1 Instruction manual
1 Exploded drawing
• Checkfordamagetothetool,partsoraccessorieswhichmay
have occurred during transport.
• Takethetimetothoroughlyreadandunderstandthismanualpriorto
operation.
• Removethesawfromthepackagingmaterialcarefully.
• Releasetheheadlockdownknobtoraisetheheadofthemachine.
Description (fig. A1–A5)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
A1
1 On/off switch
2 Head lock up release lever
3 Additional saw bench table locking knob
4 Moveable lower blade guard
5 Fixed table
6 Blade slot
7 Mitre lever
8 Mitre latch
9 Rotating table/mitre arm
10 Mitre scale
11 Fence
12 Bevel clamp handle
13 Head lock down knob
A2
14 Saw bench table
15 Riving knife
16 Upper saw blade guard
17 Rip fence
18 Fixed lower guard (for use in bench saw position)
19 Attachment mounting holes
OPTIONAL ACCESSORIES
A3
20 Table end plate
21 Support guide rails
22 Material support plate
23 Material clamp
24 Swivelling stop
25 Adjustable stand 760 mm (max. height)
26 Legstand
A4
27 Length stop for short workpieces (to be used with guide rails [21])
A5
26 Legstand
29 Roller table
INTENDED USE
Your DW711 table top mitre saw has been developed for professional
applications. This high precision machine can be easily and quickly set to
crosscut, bevel, mitre, or compound mitre.
DO NOT use under wet conditions or in presence of flammable liquids or
gases.
These mitre saws are professional power tools.
DO NOT let children come into contact with the tool. Supervision is required
when inexperienced operators use this tool.
Electrical safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Machines in the scope of EN 61029 are not allowed for production use.
In case of cord replacement the tool must only be repaired by an authorized
service agent or by qualified electrician.
Mains Plug Replacement
(U.K. & Ireland Only)
DANGER:
• Shouldyourmainsplugneedreplacingandyouarecompetentto
dothis,proceedasinstructedbelow.Ifyouareindoubt,contactan
authorizedDeWALT repair agent or a qualified electrician.
• Disconnecttheplugfromthesupply.
• Cutoffthepluganddisposeofitsafely;aplugwithbaredcopper
conductors is dangerous if engaged in a live socket outlet.
• Onlyfit13AmperesBS1363Aapprovedplugsfittedwiththecorrectly
rated fuse (1).
• Thecablewirecolours,oraletter,willbemarkedattheconnection
points of most good quality plugs. Attach the wires to their respective
points in the plug (see below). Brown is for Live (L) (2) and Blue is for
Neutral (N) (4).
• Beforereplacingthetopcoverofthemainsplugensurethatthecable
restraint (3) is holding the outer sheath of the cable firmly and that the
two leads are correctly fixed at the terminals crews.
