Bedienungsanleitung DeWalt DW716E (Seite 32 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546159

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

Mains Plug Replacement

(U.K. & Ireland only)

• Should your mains plug need replacing and you are competent to

do this, proceed as instructed below. If you are in doubt, contact an

authorized DEWALT repair agent or a qualified electrician.

• Disconnect the plug from the supply.

• Cut off the plug and dispose of it safely; a plug with bared copper

conductors is dangerous if engaged in a live socket outlet.

• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly

rated fuse (1).

• The cable wire colours, or a letter, will be marked at the connection

points of most good quality plugs. Attach the wires to their respective

points in the plug (see below). Brown is for Live (L) (2) and Blue is for

Neutral (N) (4).

• Before replacing the top cover of the mains plug ensure that the cable

restraint (3) is holding the outer sheath of the cable firmly and that the

two leads are correctly fixed at the terminal screws.

WARNING: Never use a light socket.

Never connect the live (L) or neutral (N) wires to the earth pin

marked E or .

Fitting a mains plug to 115 V units (U.K. & Ireland only)

• The plug should be fitted by a competent person. If you are in doubt,

contact an authorized DEWALT repair agent or a qualified electrician.

The wires are coloured according to the following code:

live = brown

neutral = blue

• Do not connect the blue or brown wire to the earth terminal in the plug.

Connect as follows:

brown to terminal marked ‘L’

blue to terminal marked ‘N’

The plug fitted should comply with BS EN 60309 (BS4343), 32 Amps.

WARNING: Always ensure that the cable clamp is correctly and

securely fitted to the sheath of the cable.

Using an Extension Cable

If an extension cable is required, use an approved extension cable suitable

for the power input of this tool (see technical data).

The minimum conductor size is 1.5 mm

When using a cable reel, always unwind the cable completely.

Also refer to the table below.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0 - 2.0 6 6 6 6 6 10

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Voltage Drops

In rush currents cause short-time voltage drops. Under unfavourable power

supply conditions, other equipment may be affected.

If the system impedance of the power supply is lower than 0.25 Ω,

disturbances are unlikely to occur.

ASSEMBLY

WARNING: To reduce the risk of injury, turn off tool and

disconnect from power source before attempting to move

it, changing accessories or making any adjustments accept as

written in laser adjustment instructions.

Unpacking (fig. B)

• Remove the saw from the packing material carefully using the carrying

handle (9).

• Press down the operating handle (10) and pull out the lock down pin

(18), as shown.

• Gently release the downward pressure and allow the arm to rise to its

full height.

Bench Mounting (fig. C)

• Holes (23) are provided in all four feet to facilitate bench mounting.

Two different sized holes are provided to accommodate different sizes

of bolts. Use either hole; it is not necessary to use both. Always mount

your saw firmly to prevent movement. To enhance the portability, the

tool can be mounted to a piece of 12.5 mm or thicker plywood which

can then be clamped to your work support or moved to other job sites

and reclamped.

• When mounting your saw to a piece of plywood, make sure that the

mounting screws do not protrude from the bottom of the wood.

The plywood must sit flush on the work support. When clamping the

saw to any work surface, clamp only on the clamping bosses where

the mounting screw holes are located. Clamping at any other point will

interfere with the proper operation of the saw.

• To prevent binding and inaccuracy, be sure the mounting surface is not

warped or otherwise uneven. If the saw rocks on the surface, place a

thin piece of material under one saw foot until the saw is firm on the

mounting surface.

Mounting the Saw Blade (fig. D1–D5)

WARNING: To reduce the risk of injury, turn off tool and

disconnect from power source before attempting to move it,

changing accessories or making any adjustments accept as

written in laser adjustment instructions.

Never depress the spindle lock button while the blade is under

power or coasting.

Do not cut ferrous metal (containing iron or steel) or masonry or

fiber cement product with this mitre saw.

• Depress the head lock up release lever (11) to release the lower guard

(2), then raise the lower guard as far as possible.

• Using the bit (29) in the handgrip end of the supplied wrench (21),

loosen the guard bracket screw (30) sufficiently to allow the angled

corner piece (31) to pass between the head of the screw and the

guard. This will allow the guard bracket (32) to be raised enough to

permit access to the blade locking screw (33).

• With the lower guard held in the raised position by the guard bracket

screw (30) depress the spindle lock button (13) with one hand, then

use the supplied wrench (21) in the other hand to loosen the left-hand

threaded blade locking screw (33) by turning clockwise.

ENGLISH

DeWalt DW716E Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info