Bedienungsanleitung DeWalt DW717XPS T 4 (Seite 36 von 144) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546167

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

WARNING:

• Do not perform sliding cuts on workpieces smaller than

76.2 mm.

• Remember to lock the saw head in the rear position when the

sliding cuts are ﬁ nished.

Mitre cross-cut (ﬁ g. A1 & N)

• Release the mitre lever (4) and depress the mitre latch (5).

• Move the arm left or right to the required angle. The mitre latch will

automatically locate at 10°, 15°, 22.5°, 31.62° and 45° both left and

right. If any intermediate angle is required hold the head ﬁ rmly and lock

by tightening the mitre lever.

• Always ensure that the mitre lever is locked tightly before cutting.

• Proceed as for a vertical straight cross-cut.

WARNING: When mitring the end of a piece of wood with a

small off-cut, position the wood to ensure that the off-cut is to

the side of the blade with the greater angle to the fence; i.e. left

mitre, off-cut to the right - right mitre, off-cut to the left.

Bevel cuts (ﬁ g. A1, A2 & O)

Bevel angles can be set from 48° left to 48° right and can be cut with the

mitre arm set between zero and a maximum of 45° mitre position right or

left.

Left bevel

• Slide the upper part of the left side fence (3) to the left as far as it will go.

• Loosen the bevel clamp handle (21), lift the bevel latch (20) and set the

bevel as desired.

• The bevel latch automatically locates at 22.5°, 33.85° and 45°. If

any intermediate angle is required, hold the head ﬁ rmly and lock by

tightening the bevel clamp handle (21).

• Proceed as for a vertical straight cross-cut.

Right bevel

• Slide the upper part of the right side fence (8) to the right as far as it will

go.

• Proceed as for a left bevel cut.

Quality of cut

The smoothness of any cut depends on a number of variables, e.g. the

material being cut. When smoothest cuts are desired for moulding and

other precision work, a sharp (60 tooth carbide) blade and a slower,

even cutting rate will produce the desired results.

WARNING: Ensure that the material does not creep while

cutting; clamp itsecurely in place. Always let the blade come to

a full stopbefore raising the arm. If small fibres of wood still split

out atthe rear of the workpiece, stick a piece of masking tape

on thewood where the cut will be made. Saw through the tape

andcarefully remove tape when finished.

Clamping the workpiece (ﬁ g. A6, U)

WARNING: A workpiece that is clamped, balanced and secure

before a cut may become unbalanced after a cut is completed.

An unbalanced load may tip the saw or anything the saw is

attached to, such as a table or workbench. When making a cut

that may become unbalanced, properly support the workpiece

and ensure the saw is firmly bolted to a stable surface. Personal

injury may occur.

WARNING: The clamp foot must remain clamped above the

base of the saw whenever the clamp is used. Always clamp the

workpiece to the base of the saw – not to any other part of the

work area. Ensure the clamp foot is not clamped on the edge of

the base of the saw.

CAUTION: Always use a work clamp to maintain control and

reduce the risk of personal injury and workpiece damage.

Use the material clamp (30) provided with your saw. The left or right fence

will slide from side to side to aid in clamping. Other aids such as spring

clamps, bar clamps or C-clamps may be appropriate for certain sizes and

shapes of material.

TO INSTALL CLAMP

1. Insert it into the hole behind the fence. The clamp should be facing

toward the back of the mitre saw. The groove on the clamp rod should

be fully inserted into the base. Ensure this groove is fully inserted into

the base of the mitre saw. If the groove is visible, the clamp will not be

secure.

2. Rotate the clamp 180° toward the front of the mitre saw.

3. Loosen the knob to adjust the clamp up or down, then use the fine

adjust knob to firmly clamp the workpiece.

NOTE: Place the clamp on the opposite side of the base when beveling.

ALWAYS MAKE DRY RUNS (UNPOWERED) BEFORE FINISH CUTS TO

CHECK THE PATH OF THE BLADE. ENSURE THE CLAMP DOES NOT

INTERFERE WITH THE ACTION OF THE SAW OR GUARDS.

Support for long pieces (ﬁ g. A5)

• Always support long pieces.

• For best results, use the extension work support (29) to extend the

table width of your saw (available from your dealer as an option).

Support long workpieces using any convenient means such as

saw-horses or similar devices to keep the ends from dropping.

Cutting picture frames, shadow boxes & other four sided projects

(ﬁ g. P1 & P2)

Trim moulding and other frames

Try a few simple projects using scrap wood until you develop a “feel” for

your saw. Your saw is the perfect tool for mitring corners like the one

shown in ﬁ g. P1. The joint shown has been made using either bevel

adjustment.

- Using bevel adjustment

The bevel for the two boards is adjusted to 45° each, producing a 90° corner.

The mitre arm is locked in the zero position. The wood is positioned with

the broad ﬂ at side against the table and the narrow edge against the fence.

- Using mitre adjustment

The same cut can be made by mitring right and left with the broad surface

against the fence.

The two sketches (ﬁ g. P1 & P2) are for four side objects only. As the

number of sides changes, so do the mitre and bevel angles. The chart

below gives the proper angles for a variety of shapes, assuming that all

sides are of equal length. For a shape that is not shown in the chart,

divide 180° by the number of sides to determine the mitre or bevel angle.

No. of sides Angle mitre or bevel

4 45°

5 36°

6 30°

7 25.7°

8 22.5°

9 20°

10 18°

Compound mitre (ﬁ g. Q1 & Q2)

A compound mitre is a cut made using a mitre angle (ﬁ g. P2) and a bevel

angle (ﬁ g. P1) at the same time. This is the type of cut used to make

frames or boxes with slanting sides like the one shown in ﬁ g. Q1.

WARNING: If the cutting angle varies from cut to cut, check

that the bevel clamp knob and the mitre lock knob are securely

tightened. These knobs must be tightened after making any

changes in bevel or mitre (ﬁ g. Q1 & Q2).

ENGLISH

DeWalt DW717XPS T 4 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info