Bedienungsanleitung DeWalt DW718XPS T 3 (Seite 33 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546174

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

ENGLISH

Do not cut ferrous (iron and steel) materials, fibre cement or masonry

with this saw!

• Make sure to use the kerf plate. Do not operate the machine if the kerf

slot is wider than 10 mm.

Switching on and off (fig. L)

A hole (58) is provided in the on/ off switch (1) for insertion of a padlock to

lock the tool.

• To run the tool, press the on/off switch (1).

• To stop the tool, release the switch.

Setting the variable speed (fig. L)

The speed control dial (13) can be used for advance setting of the required

range of speed.

• Turn the speed control dial (13) to the desired range, which is indicated

by a number.

• Use high speeds for sawing soft materials such as wood.

Use low speeds for sawing metal.

Basic saw cuts

Vertical straight cross cut (fig. A1, A2 & M)

• Release the mitre lever (4) and depress the mitre latch (5) to release the

mitre arm.

• Engage the mitre latch at the 0° position and tighten the mitre lever.

• Place the wood to be cut against the fence (3 & 8).

• Take hold of the operating handle (11) and depress the head lock up

release lever (12) to release the head.

• Press the trigger switch (1) to start the motor.

• Depress the head to allow the blade to cut through the timber and

enter the plastic kerf plate (9).

• After completing the cut, release the switch and wait for the saw blade

to come to a complete standstill before returning the head to its upper

rest position.

Performing a sliding cut (fig. N)

The guide rail allows cutting larger workpieces from 50 x 100 mm up to

500 x 1000 mm using an out-down-back sliding motion.

• Release the rail lock knob (16).

• Pull the saw head towards you and switch the tool on.

• Lower the saw blade into the workpiece and push the head back to

complete the cut.

• Proceed as described above.

• Do not perform sliding cuts on workpieces smaller than

50 x 100 mm.

• Remember to lock the saw head in the rear position when the

sliding cuts are finished.

Vertical mitre cross-cut (fig. A1, A2 & O)

• Release the mitre lever (4) and depress the mitre latch (5).

• Move the arm left or right to the required angle. The mitre latch will

automatically locate at 10°, 15°, 22.5°, 31.62° and 45° both left and

right, and at 60° left and 50° right. If any intermediate angle is required

hold the head firmly and lock by tightening the mitre lever.

• Always ensure that the mitre lever is locked tightly before cutting.

• Proceed as for a vertical straight cross-cut.

When mitring the end of a piece of wood with a small off-cut,

position the wood to ensure that the off-cut is to the side of

the blade with the greater angle to the fence; i.e. left mitre,

off-cut to the right - right mitre, off-cut to the left.

Bevel cuts (fig. A1, A2 & P)

Bevel angles can be set from 48° left to 48° right and can be cut with the

mitre arm set between zero and a maximum of 45° mitre position right or

left.

Left bevel

• Slide the upper part of the left side fence (3) to the left as far as it will go.

• Loosen the bevel clamp handle (21), lift the bevel latch (20) and set the

bevel as desired.

• The bevel latch automatically locates at 22.5°, 33.85° and 45°. If any

intermediate angle is required, hold the head firmly and lock by

tightening the bevel clamp handle (21).

• Proceed as for a vertical straight cross-cut.

Right bevel

• Slide the upper part of the right side fence (8) to the right as far as it will

go.

• Proceed as for a left bevel cut.

Quality of cut

The smoothness of any cut depends on a number of variables, e.g. the

material being cut. When smoothest cuts are desired for moulding and

other precision work, a sharp (60 tooth carbide) blade and a slower,

even cutting rate will produce the desired results.

Ensure that the material does not creep while cutting; clamp it

securely in place. Always let the blade come to a full stop before

raising the arm. If small fibres of wood still split out at the rear

of the workpiece, stick a piece of masking tape on the wood

where the cut will be made. Saw through the tape and

carefully remove tape when finished.

Body and hand position

Proper positioning of your body and hands when operating the mitre saw

will make cutting easier, more accurate and safer.

• Never place your hands near the cutting area.

• Place your hands no closer than 150 mm from the blade.

• Hold the workpiece tightly to the table and the fence when cutting.

Keep your hands in position until the switch has been released and the

blade has completely stopped.

• Always make dry runs (without power) before finish cuts so that you

can check the path of the blade.

• Do not cross your hands.

• Keep both feet firmly on the floor and maintain proper balance.

• As you move the saw arm left and right, follow it and stand slightly to

the side of the saw blade.

• Sight through the guard louvres when following a pencil line.

Clamping the workpiece (fig. A6)

• Whenever possible, clamp the wood to the saw.

• For best results use the clamp (29) made for use with your saw.

Clamp the workpiece to the fence whenever possible. You can clamp

to either side of the saw blade; remember to position your clamp

against a solid, flat surface of fence.

Always use a material clamp when cutting non-ferrous metals.

Support for long pieces (fig. A4)

• Always support long pieces.

• For best results, use the extension work support (27) to extend the

table width of your saw (available from your dealer as an option).

Support long workpieces using any convenient means such as

saw-horses or similar devices to keep the ends from dropping.

DeWalt DW718XPS T 3 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info