Bedienungsanleitung DeWalt DW718XPS T 4 (Seite 35 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546175

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

ENGLISH

• Place your hands no closer than 150 mm from the blade.

• Hold the workpiece tightly to the table and the fence when cutting.

Keep your hands in position until the switch has been released and the

blade has completely stopped.

• Always make dry runs (without power) before ﬁ nish cuts so that you

can check the path of the blade.

• Do not cross your hands.

• Keep both feet ﬁ rmly on the ﬂ oor and maintain proper balance.

• As you move the saw arm left and right, follow it and stand slightly to

the side of the saw blade.

• Sight through the guard louvres when following a pencil line.

Clamping the workpiece (ﬁ g. A6)

• Whenever possible, clamp the wood to the saw.

• For best results use the clamp (29) made for use with your saw.

Clamp the workpiece to the fence whenever possible. You can clamp

to either side of the saw blade; remember to position your clamp

against a solid, ﬂ at surface of fence.

WARNING: Always use a material clamp when cutting non-

ferrous metals.

Support for long pieces (ﬁ g. A4)

• Always support long pieces.

• For best results, use the extension work support (27) to extend the

table width of your saw (available from your dealer as an option).

Support long workpieces using any convenient means such as

saw-horses or similar devices to keep the ends from dropping.

Cutting picture frames, shadow boxes & other four sided projects

(ﬁ g. Q1 & Q2)

Trim moulding and other frames

Try a few simple projects using scrap wood until you develop a “feel” for

your saw. Your saw is the perfect tool for mitring corners like the one

shown in ﬁ g. Q1. The joint shown has been made using either bevel

adjustment.

- Using bevel adjustment

The bevel for the two boards is adjusted to 45° each, producing a 90° corner.

The mitre arm is locked in the zero position. The wood is positioned with

the broad ﬂ at side against the table and the narrow edge against the fence.

- Using mitre adjustment

The same cut can be made by mitring right and left with the broad surface

against the fence.

The two sketches (ﬁ g. Q1 & Q2) are for four side objects only. As the

number of sides changes, so do the mitre and bevel angles. The chart

below gives the proper angles for a variety of shapes, assuming that all

sides are of equal length. For a shape that is not shown in the chart,

divide 180° by the number of sides to determine the mitre or bevel angle.

No. of sides Angle mitre or bevel

4 45°

5 36°

6 30°

7 25.7°

8 22.5°

9 20°

10 18°

Compound mitre (ﬁ g. R1 & R2)

A compound mitre is a cut made using a mitre angle (ﬁ g. Q2) and a bevel

angle (ﬁ g. Q1) at the same time. This is the type of cut used to make

frames or boxes with slanting sides like the one shown in ﬁ g. R1.

WARNING: If the cutting angle varies from cut to cut, check

that the bevel clamp knob and the mitre lock knob are securely

tightened. These knobs must be tightened after making any

changes in bevel or mitre.

• The chart shown below will assist you in selecting the proper bevel

and mitre settings for common compound mitre cuts. To use the chart,

select the desired angle “A” (ﬁ g. R2) of your project and locate that

angle on the appropriate arc in the chart. From that point follow the

chart straight down to ﬁ nd the correct bevel angle and straight across

to ﬁ nd the correct mitre angle.

• Set your saw to the prescribed angles and make a few trial cuts.

• Practice ﬁ tting the cut pieces together.

• Example: To make a 4 sided box with 25° exterior angles (angle “A”)

(ﬁ g. R2), use the upper right arc. Find 25° on the arc scale. Follow the

horizontal intersecting line to either side to get the mitre angle setting

on the saw (23°). Likewise follow the vertical intersecting line to the top

or bottom to get the bevel angle setting on the saw (40°). Always try

cuts on a few scrap pieces of wood to verify the settings on the saw.

SET THIS BEVEL ANGLE ON SAW

SET THIS MITER ANGLE ON SAW

ANGLE OF SIDE OF BOX (ANGLE"A")

SQUARE BOX

6 SIDED BOX

8 SIDED BOX

Cutting base mouldings

The cutting of base moulding is performed at a 45° bevel angle.

• Always make a dry run without power before making any cuts.

• All cuts are made with the back of the moulding laying ﬂ at on the saw.

Inside corner

- Left side

• Position the moulding with top of the moulding against the fence.

• Save the left side of the cut.

- Right side

• Position the moulding with the bottom of the moulding against the

fence.

• Save the left side of the cut.

Outside corner

- Left side

• Position the moulding with the bottom of the moulding against the

fence.

• Save the right side of the cut.

- Right side

• Position the moulding with top of the moulding against the fence.

• Save the right side of the cut.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW718XPS T 4 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info