546503

DeWalt DW720K Seite 34

34
Zoom out
Zoom in
Vorherige Seite
1/144
Nächste Seite
en - 5 26
ENGLISH
Make sure that the ring (44) of the arbor nut (39) is against the
outer flange (fig. E1).
• Tighten the arbor nut (39) by turning counterclockwise.
Checking that the arm is parallel to the table top (fig. A2, D3 & E2)
• Tighten the riplock (15) with the blade in front position (fig. A2).
• Lower the blade until it only just touches the table top (4) (fig. E2).
• Release the levers (9) and (10) (fig. A1).
• Swing the arm so that the blade skims the table top (4) across its width.
• If required, adjust the front adjusting bolt (34) (fig. D3).
• Repeat this procedure with the blade in rear position and adjust the
rear bolt if required.
Checking that the blade is perpendicular to the table top (fig. A2 & E3)
• Bring the arm back to central position and tighten the riplock (15) (fig. A2).
• Place a steel square (45) against the blade body (fig. F3).
• If adjustment is required, proceed as follows:
• Remove the bevel pointer disk (46) by loosening the two screws (47).
• Loosen all three Allen screws that will be exposed in this way.
• Place an Allen key in the motor arbor and tap until the blade is flat
against the square.
• Firmly tighten all fasteners.
It is particularly important to tighten the central Allen screw.
• Replace the bevel pointer disk (46).
Checking that the crosscut travel is perpendicular to the fence
(fig. E4 & E5)
• Lock the blade in front of the fence (fig. E4).
• Place a square (45) on a piece of board and against the fence and just
touching the blade as shown.
• Unlock the riplock, pull the blade towards you to check that the blade
traverses parallel to the square.
• If adjustment is required, proceed as follows:
• With the mitre latch lever (9) engaged in 0° position, release the mitre
clamp lever (10) (fig. E5).
• Loosen the locknuts (48) on each side of the arm (fig. E5).
• To adjust the arm to the left, loosen the stud on the righthand side of
the arm and tighten the opposite stud.
• To adjust the arm to the right, loosen the stud on the lefthand side of
the arm and tighten the opposite stud.
• Proceed in small steps and check the adjustment after each step with
the levers (9) and (10) engaged.
Do not overtighten the studs.
• Tighten the locknuts (48).
Checking that the blade is perpendicular to the fence (fig. E6)
• Unlock the yoke clamp lever (49) press the yoke latch (50).
• Rotate the motor through 90° as shown.
• If the motor shows a certain play, tighten the nut (51).
• Place the blade against the fence and check that it is parallel to the fence.
• If adjustment is required, proceed as follows:
• Loosen the two bolts (52) installed crosswise under the yoke.
• Insert the Allen key into the motor arbor.
• Adjust the blade position and tighten the bolts (52).
Mounting and adjusting the blade guard assembly (fig. F1 - F5)
The blade guard (3) is a multifunctional assembly which offers the following
safety features (fig. F1):
- Upper guard (53) (fig. G1) and spring held rear guard (54) (fig. F2) for
full blade protection.
- Dust extraction adapter (55) for cross and rip cutting.
- Anti-kickback fingers (56) for use in ripping mode.
- Adjustable finger guard (57) for use when cross-cutting.
- Riving knife (58) to prevent the workpiece binding on the blade when
ripping.
• Release the bevel clamp lever (19) and pull out the bevel latch (21) (fig. D2)
to tilt the motor as shown for optimum access (fig. F3).
• Remove the guard retaining wing nut (59) and washer (60) (fig. F3).
• Loosen the locking screw (61) and turn the retaining bracket (62) anti-
clockwise until the spring held rear guard (54) can be lifted off its
support lug (63) (fig. F2).
• Unhook the two springs (64) at the top only.
• Rotate the unhooked rear blade guard (54) as shown (fig. F2).
• Lower the guard assembly over the blade (fig. F3).
• Secure the guard assembly using the wing nut (59) and washer (60)
(fig. F3).
• Bring the spring held rear blade guard (54) and the retaining bracket (62)
into their original position (fig. F2).
• To remove the guard assembly, proceed in reverse order.
The teeth of a new blade are very sharp and can be
dangerous.
Adjusting the guard assembly controls (fig. F2 - F5)
Adjusting the riving knife for ripping
• Loosen the two knobs (65) and slide the riving knife (58) down until the
tip is approximately 10 mm from the table top (fig. F2 & F4).
The riving knife should be correctly set; the distance between the
toothed rim and the riving knife (58) should be 1-3 mm (fig. F4).
Adjusting the anti-kickback fingers for (bevel) ripping (fig. F5)
• Loosen the knob (66) and lower the bracket (67) until the hold down
spring (68) just touches the surface of the workpiece.
• The tips of the anti-kickback fingers (56) should now be 3 mm below
the surface of the workpiece and the angle should now be as shown in
figure F5.
• For bevel ripping, loosen the Allen screw (69) and set the anti-kickback
fingers to the required angle.
Adjusting the riving knife, finger guard and anti-kickback fingers for
cross-cutting (fig. F2)
• For cross-cutting, adjust the riving knife and anti-kickback fingers up
and out of the way.
• Loosen the lever (70) to position the finger guard (57) just above the
workpiece and lock the lever (70).
Scale adjustments (fig. G1 - G5)
Rip scale
Ripping can be done with the motor in two positions. Each mode requires
its own direction of feed:
Position Direction of feed
- In-rip from right to left (fig. G1)
- Out-rip from left to right (fig. G2)
The pointer (71) indicating the ripping width on the rip scale (72) is
adjustable (fig. G3):
• Place the fence in rearmost position.
• Place a board of 24 mm against the fence.
• Unlock the yoke clamp lever (49), press the yoke latch (50) (fig. H1) and
position the motor in out-rip position (fig. G1).
• Move the yoke assembly along the radial arm until the blade just
touches the edge of the material.
… 34 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

dewalt-dw720k

Suche zurücksetzen

  • Necesito el diagrama de la conexión del cable 110 a la caja del motor donde esta el condensador de la sierra Radial de brazo DW725 Eingereicht am 7-12-2018 01:37

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für DeWalt DW720K wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info