Bedienungsanleitung DeWalt DW738 T 3 (Seite 22 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546444

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

8. Dress properly.

Do not wear loose clothing or jewellery, as these can be caught in

moving parts. Non-skid footwear is recommended when working

outdoors. Wear protective hair covering to contain long hair.

9. Use protective equipment.

Always use safety glasses. Use a face or dust mask if working

operations create dust or flying particles. If these particles might

be considerably hot, also wear a heat-resistant apron. Wear ear

protection at all times. Wear a safety helmet at all times.

10. Connect dust extraction equipment.

If devices are provided for the connection of dust extraction and

collection facilities, ensure that these are connected and properly

used.

11. Do not abuse the cord.

Never yank the cord to disconnect if from the socket. Keep

the cord away from heat, oil and sharp edges. Never carry the tool

by its own cord.

12. Secure work.

Where possible use clamps or a vice to hold the work. It is safer

than using your hand and it frees both hands to operate the tool.

13. Do not overreach.

Keep proper footing and balance at all times.

14. Maintain tools with care.

Keep cutting tools sharp and clean for better and safer

performance. Follow instructions for lubricating and changing

accessories. Inspect tools periodically and if damaged have them

repaired by an authorised service facility. Keep handles dry, clean

and free from oil and grease.

15. Disconnect tools.

When not in use, before servicing and when changing accessories

such as blades, bits and cutters, disconnect tool from the power

supply.

16. Remove adjusting keys and wrenches.

Form the habit of checking to see that adjusting keys and

wrenches are removed from the tool before operating the tool.

17. Avoid unintentional starting.

Do not carry the tool with a finger on the switch. Be sure that the

tool is in the “off” position before plugging in.

18. Use outdoor extension leads.

Before use, inspect the extension cable and replace if damaged.

When the tool is used outdoors, use only extension cords intended

for outdoor use and marked accordingly.

19. Stay alert.

Watch what you are doing. Use common sense. Do not operate

the tool when you are tired or under the influence of drugs or

alcohol.

20. Check for damaged parts.

Before use, carefully check the tool and mains cable to determine

that it will operate properly and perform its intended function.

Check for alignment of moving parts, binding of moving parts,

breakage of parts, mounting and any other conditions that may

affect its operation. A guard or other part that is damaged should

be properly repaired or replaced by an authorized service centre

unless otherwise indicated in this instruction manual. Have any

damaged or defective switches replaced by an authorised service

center. Do not use the tool if the switch does not turn it on and off.

Never attempt any repairs yourself.

WARNING! The use of any accessory or attachment or

performance of any operation with this tool other than

those recommended in this instruction manual may present

a risk of personal injury.

Additional Safety Instructions for Bandsaws

• Before work checks that the machine is placed on an even surface

with sufficient stability.

• In case of an accident or machine failure immediately switch the

machine off and disconnect from the power source.

• Report the failure and mark the machine in suitable form to prevent

other people from using the defective machine.

• When the bandsaw blade is blocked caused by abnormal feed

force during cutting, switch the machine off and disconnect from

power supply. Remove the workpiece and ensure that the bandsaw

blade runs free. Switch the machine on and start new cutting

operation with reduced feed force.

• Refrain from removing any cut-offs or other parts of the work piece

from the cutting area whilst the machine is running.

• Provide adequate general or localized lighting

• Ensure the operator is adequately trained in use, adjustment and

operation of the machine.

• Switch the machine off when unattended.

• Connect the band saw to a dust collection when sawing wood.

Always consider factors influencing exposure of dust such as:

- Type of material to be machined (Chip board produces more

dust than wood).

- Correct adjustment of bandsaw blade.

- Ensure that the local extraction as well as hoods, baffles and

chutes are properly adjusted.

- Dust extractor with air velocity not less than 20 m/s.

• All time wear suitable personal protective equipment as:

- Hearing protection to reduce the risk of induced hearing loss.

- Respiratory protection to produce the risk of inhalation of

harmful dust.

- Gloves for handling the bandsaw blade and rough material.

• When straight cutting against rip fence use the push stick.

• Always place the guide (rip fence) on the lower side of the table

when cutting with the table inclined.

• When cutting round material use a suitable holding device to

prevent twisting of the workpiece.

• Before starting operation check correct adjustment and functionality

of the band saw guards.

• Workpiece sizes

Never cut workpiece smaller than 20mm.

Without additional support the machine is designed to accept

the maximum workpiece size of:

Height 150mm by width 230mm by length 700mm.

Longer workpiece needs to be supported by suitable additional

table.

• Keep other persons away from the work area. Do not allow

children, visitors or animals to come near the work area or to touch

the tool or mains cable.

• Use appropriate tool. The intended use is described in this

instruction. Do not force the tool. It does the job better and safer at

the rate for which it is intended.

• This machine is not designed for serial or con conveyor belt

production.

• Keep proper footing and balance at all times.

• Always use safety glasses. Use a face dust mask if working

operations create dust or flying particle. If these particles might

be considerable hot, also wear a heat-resistant apron. Wear ear

protection and safety helmet at all times

• Select the correct bandsaw blade for the different type of speed

settings and the material to be cut.

• Observe the maximum speed marked on the bandsaw blade

packaging.

• Do not use bandsaw blades that do not conform to the dimensions

stated in the technical data.

• Do not use deformed or damaged bandsaw blades.

• When performing bevel cuts, ensure that the rip fence is fixed on

the lower side of the table.

• Keep the push stick in its place when nut in use.

• Do not overreach. Keep proper footing and balance at all times.

• Never clean the machine whilst the saw band is in motion.

DeWalt DW738 T 3 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info