Bedienungsanleitung DeWalt DW831 T 3 (Seite 30 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

548022

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

DW840 - Mounting (fig. B2 & C2)

• Place the angle grinder on a table, spindle up.

• Align the lugs (6) with the slots (7).

• Press the guard (8) down and turn it in the

direction of the arrow (fig. B2).

• Securely tighten the screws (9).

DW840 - Removing

• To remove the guard, proceed in reverse order.

MOUNTING AND REMOVING A GRINDING WHEEL OR

CUTTING DISK (FIG. D & E)

• Place the tool on a table, guard up.

• Fit the spacer (11) correctly onto the spindle (10).

• Place the grinding wheel or cutting disk on the

spacer.

• Screw the threaded flange (12) onto the

spindle (10).

• Press the spindle lock (5) and rotate the grinding

wheel or cutting disk until it locks in position.

• Tighten the threaded flange using the two-pin

spanner (13) supplied.

• Release the spindle lock.

• To remove the grinding wheel or cutting disk,

loosen the threaded flange using the two-pin

spanner (while the spindle lock is engaged).

MOUNTING THE SIDE HANDLE (FIG. F)

• Screw the side handle (3) tightly into one of the

holes (14) on either side of the gear case.

Instructions for use

WARNING:

• Always observe the safety instructions

and applicable regulations.

• Ensure all materials to be ground or cut

are secured in place.

• Apply only a gentle pressure to the

tool. Do not exert side pressure on the

grinding wheel or cutting disk.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

• Check that mounted wheels are

correctly fitted according to the

instructions given in this manual.

• Ensure that blotters are used when they

are provided with the abrasive wheel

and when they are required.

• Do not use separate reducing bushings

or adapters to adapt large hole abrasive

wheels.

• Never use the tool without the guard in

place.

• Be aware, the wheel continues to rotate

after the tools is switched off.

Prior to operation:

• Install the appropriate guard and disk or wheel.

Do not use excessively worn disks or wheels.

• Be sure the spacer and threaded flange are

mounted correctly.

• Make sure the disk or wheel rotates in the

direction of the arrows on the accessory and the

tool.

• Do not use cutting-off wheels for side grinding.

• Ensure that sparks resulting from use do not

create hazard e.g. do not hit persons, or ignite

flammable substances.

OPERATION

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure

that the tool is off.

SWITCHING ON AND OFF (FIG. G)

CAUTION: Hold the side handle and

body of the tool firmly to maintain control

of the tool at start up and during use

and until the wheel or accessory stops

rotating. Make sure the wheel has come

to a complete stop be fore laying the tool

down.

• To run the tool, press the lock-off button (2) and

the ON/OFF-switch (1). For continuous operation,

press the lock-on button (2) and release the

ON/OFF-switch.

• To stop the tool, release the ON/OFF-switch.

To stop the tool in continuous operation, press

the ON/OFF-switch once more.

WARNING: Do not switch the tool ON or

OFF when under load.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW831 T 3 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DW831 T 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info