548694
25
Zoom out
Zoom in
Vorherige Seite
1/96
Nächste Seite
25
Mount the round handle (22) using the two
screws (23).
Fit one screw in the top hole (7) and the other in
one of the side holes (8).
Instructions for use
Always observe the safety instructions
and applicable regulations.
Ensure all materials to be ground or cut
are secured in place.
Apply only a gentle pressure to the tool.
Do not exert side pressure on the
grinding wheel or cutting disc.
Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Prior to operation:
Install the guard and appropriate disc or wheel.
Do not use excessively worn discs or wheels.
Be sure the spacer and threaded flange are
mounted correctly.
Make sure the disc or wheel rotates in the
direction of the arrows on the accessory and the
tool.
Switching on and off (fig. A)
The on/off-switch of your angle grinder is equipped
with an unlocking switch or a locking switch for
continuous operation.
(U.K. & France only) - On/off-switch (1) with
unlocking switch (2)
To unlock the on/off-switch, slide the unlocking
switch towards you.
To run the tool, press the on/off-switch.
To stop the tool, release the on/off-switch.
On/off-switch (1) with locking switch (2a)
To run the tool, press the on/off-switch. The tool
now runs in continuous operation.
To stop the tool, press the locking switch briefly,
and release the on/off-switch.
Do not switch the tool on or off when
under load.
ENGLISH
DW491 - Using the diamond guard DE8501
(option) (fig. C)
The diamond guard is used for cutting concrete and
masonry, when accurate cutting depth adjustment
or dust extraction are required.
Mount the diamond guard as described above.
Connect a dust extractor to the outlet (17).
Set the cutting depth using the ruler knob in the
front plate (13).
Observe the safety instructions applying
to diamond cutting discs.
Use a suitable diamond cutting disc
(check the data of the manufacturer).
The maximum rotation speed on the cutting
disc must not be lower than that of the tool.
Do not use cutting discs with a diameter
exceeding 230 mm.
Fire hazard! Do not use the dust
extractor when cutting metal!
Make sure that the dust extractor used is
suitable for the material to be cut and the
Diamond guard can be connected.
DW491 - Using the round handle DE8502
(option) (fig. F)
The round handle provides greater convenience and
makes your tool very easy to handle.
Mount the round handle as described above.
Consult your dealer for further information on the
appropriate accessories.
25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für DeWalt DW852 T 4 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info