Bedienungsanleitung DeWalt DW907K T 2 (Seite 10 von 20) (Englisch)

549085

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH

charger from the power supply when

there is no battery pack in the cavity.

Unplug charger before attempting to

clean.

• DO NOT attempt to charge the battery pack

with any chargers other than the ones in

this manual. The charger and battery pack are

specifically designed to work together.

• These chargers are not intended for

any uses other than charging D

EWALT

rechargeable batteries. Any other uses

may result in risk of fire, electric shock or

electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when

disconnecting charger. This will reduce risk

of damage to electric plug and cord.

• Make sure that cord is located so that it

will not be stepped on, tripped over, or

otherwise subjected to damage or stress.

• Do not use an extension cord unless it

is absolutely necessary. Use of improper

extension cord could result in risk of fire,

electric shock, or electrocution.

• Do not place any object on top of charger

or place the charger on a soft surface that

might block the ventilation slots and result

in excessive internal heat. Place the charger

in a position away from any heat source. The

charger is ventilated through slots in the top and

the bottom of the housing.

• Do not operate charger with damaged cord

or plug — have them replaced immediately.

• Do not operate charger if it has received

a sharp blow, been dropped, or otherwise

damaged in any way. Take it to an authorized

service center.

• Do not disassemble charger; take it to an

authorized service center when service or

repair is required. Incorrect reassembly may

result in a risk of electric shock, electrocution or

fire.

• Disconnect the charger from the outlet

before attempting any cleaning. This will

reduce the risk of electric shock. Removing

the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on

standard 230V household electrical power.

Do not attempt to use it on any other

voltage. This does not apply to the vehicular

charger.

SAVE THESE INSTRUCTIONS

Chargers

Your DE9116 charger accepts DEWALT NiCd and

NiMH battery packs ranging from 7.2 V to 18 V.

Your DE9118 charger accepts DEWALT NiCd battery

packs ranging from 7.2 V to 14.4 V.

The DE9135 charger accepts 7.2 to 18 V NiCd,

NiMH or Li-Ion batteries.

These chargers require no adjustment and are

designed to be as easy as possible to operate.

Charging Procedure (ﬁ g. 2)

DANGER: Electrocution hazard.

230 volts present at charging terminals.

Do not probe with conductive objects.

Danger of electric shock or

electrocution.

1. Plug the charger (k) into an appropriate outlet

before inserting battery pack.

2. Insert the battery pack into the charger. The red

(charging) light will blink continuously indicating

that the charging process has started.

3. The completion of charge will be indicated by

the red light remaining ON continuously. The

pack is fully charged and may be used at this

time or left in the charger.

NOTE: To ensure maximum performance and life of

NiCd, NiMH and Li-Ion batteries, charge the battery

for a minimum of 10 hours before first use.

Charging Process

Refer the table below for the state of charge of the

battery pack.

State of charge

charging – – – –

fully charged –––––––––––

hot/cold pack delay –– – –– –

replace battery pack •••••••••••

problem •• •• •• ••

Automatic Refresh

(DE9116, DE9135)

The automatic refresh mode will equalise or balance

the individual cells in the battery pack at its peak

capacity. Battery packs should be refreshed weekly

or whenever the pack no longer delivers the same

amount of work.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW907K T 2 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DW907K T 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info