Bedienungsanleitung DeWalt DW917K T 2 (Seite 28 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

549648

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

en - 5

Be sure that the battery pack is fully seated in the

charger, but do not force it. The red charging

indicator (11) will light. After approx. 1 hour, it will

switch off and the green status indicator (12) will

light. The battery pack is now fully charged and

the charger switches to maintenance mode.

• If the green indicator lights too soon the battery

pack may be too hot. Remove the battery pack

and allow it to cool before re-attempting to

charge.

• If the green indicator lights instantly, the battery

pack is fully uncharged.

• Leave the battery pack in the charger for several

minutes then re-insert.

• The battery pack can be removed at any time or

left in the charger indefinitely.

Inserting and removing the battery pack

• Insert the battery pack into the grip (7) until it

clicks in place.

• To remove the battery pack, press the two

release buttons (9) simultaneously and pull the

pack out of the grip (7).

Inserting and removing a bit (fig. A & B)

• Open the chuck by turning the sleeve (13)

counterclockwise and insert the bit shank.

• Tighten firmly by turning the sleeve clockwise

while holding the rear part of the chuck with one

hand.

• To remove the bit, proceed in reverse order.

Selecting the operating mode or adjusting the

torque (fig. C)

The collar of this tool has 5 positions for the

adjustment of the torque to suit the size of the screw

and the workpiece material. For torque adjustment,

refer to the section “Screwdriving”. Your tool can be

used in the following operating modes:

Drilling:

for steel, wood, plastics and masonry

Collar positions:

for screwdriving

• Select the drilling mode or torque by aligning the

symbol or number on the collar (4) with the

indicator (14) on the housing.

Forward/Reverse slider (fig. D)

• To select forward or reverse rotation, use the

forward/reverse slider (2) as shown (see arrows

on tool).

Always release the speed switch and

wait until the motor has come to a

complete standstill before changing the

direction of rotation.

Two gear selector (fig. E)

Your tool is fitted with a two gear selector (5) to vary

the speed/torque ratio.

1 low speed/high torque

(drilling large holes, driving large screws and

mixing paint)

2 high speed/low torque

(drilling smaller holes, drilling in wood)

For speed rates, refer to the technical data.

• Always push the two gear selector

completely forward or backward.

• Do not change gears at full speed or

during use.

Removing and fitting the chuck (fig. F & G)

• Open the chuck jaws as far as possible.

• Insert a screwdriver into the chuck and remove

the chuck retaining screw by turning clockwise

as shown in figure F.

• Tighten an Allen key into the chuck and strike it with

a hammer as shown in figure G. This will loosen the

chuck so that it can be unscrewed by hand.

• To refit the chuck, proceed in reverse order.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool.

Excessive force does not speed up

drilling but decreases tool performance

and may shorten tool life.

• To minimise stalling on break-through,

progressively reduce the drill point

pressure towards the end of the operation.

• Keep the motor running when pulling the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW917K T 2 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info