Bedienungsanleitung DeWalt DW926K T 1 (Seite 25 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

549650

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

After several charge and discharge cycles, the battery

pack will attain full capacity. Always check the mains

prior to charging the battery pack. If the mains is

functioning but the battery pack does not charge,

take your charger to an authorised DEWALT repair

agent. Whilst charging, the charger and the battery

pack may become warm to touch. This is a normal

condition and does not indicate a problem.

Do not charge the battery pack at

ambient temperatures <4 °C or >40 °C.

Recommended charging temperature:

approx. 24 °C.

• To charge the battery pack (9), insert it into the

charger (11) as shown and plug in the charger.

Be sure that the battery pack is fully seated in the

charger. The red charging indicator (12) will blink.

After approx. 1 hour, it will stop blinking and

remain on. The battery pack is now fully charged

and the charger automatically switches to

equalise mode. After approx. 4 hours, it will

switch to maintenance charge mode. The battery

pack can be removed at any time or left in the

connected charger indefinitely.

• The red charging indicator flashes rapidly to

indicate a charging problem. Reinsert the battery

pack or try a new one. If the new pack also

refuses to charge, have your charger tested by

an authorized DEWALT repair agent.

• When plugged into power sources such as

generators or sources that convert DC to AC,

the red charging indicator may blink twice, switch

off and repeat. This indicates a temporary

problem of the power source. The charger will

automatically switch back to normal operation.

Inserting and removing the battery pack

• Insert the battery pack into the grip (8) until it

clicks in place.

• To remove the battery pack, press the two

release buttons (10) simultaneously and pull the

pack out of the grip (8).

Inserting and removing bits (fig. A & B)

• Open the chuck by turning the sleeve (13)

counterclockwise and insert the bit shank.

• Place the bit in the chuck as far as it will go and

lift slightly before tightening.

• Tighten firmly by turning the sleeve clockwise.

• To remove the bit, proceed in reverse order.

Selecting the operating mode or adjusting the

torque (fig. C)

The collar of this tool has 15 positions for the

adjustment of the torque to suit the size of the screw

and the workpiece material. For torque adjustment,

refer to the section “Screwdriving”.

• Select the drilling mode or torque by aligning the

symbol or number on the collar (5) with the

indicator (14) on the housing.

Forward/reverse slider (fig. D)

• To select forward or reverse rotation, use the

forward/reverse slider (2) as shown (see arrows

on tool).

Always wait until the motor has come to

a complete standstill before changing the

direction of rotation.

DW926/DW907 - Two gear selector (fig. E)

Your tool is fitted with a two gear selector (6) to vary

the speed/torque ratio.

1 low speed/high torque

(drilling large holes, driving screws)

2 high speed/low torque

(drilling smaller holes)

For speed rates, refer to the technical data.

• Always push the two gear selector

completely forward or backward.

• Do not change gears at full speed or

during use.

Removing and fitting the chuck (fig. F & G)

• Open the chuck jaws as far as possible.

• Insert a screwdriver into the chuck and remove

the chuck retaining screw by turning clockwise

as shown in figure F.

• Tighten an Allen key into the chuck and strike it

with a hammer as shown in figure G. This will

loosen the chuck so that it can be unscrewed by

hand.

• To refit the chuck, proceed in reverse order.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW926K T 1 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info