Bedienungsanleitung DeWalt DW935K T1-2 (Seite 26 von 105) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

546205

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

21 en - 6

ENGLISH

Bevel adjustment (fig. A & B)

The bevel angle can be adjusted between 0° and 50°.

• Loosen the bevel adjustment knob (6).

• Set the bevel angle by tilting the saw shoe (12) until

the mark indicates the desired angle on the scale.

• Tighten the bevel adjustment knob (6).

Shoe adjustment for 90° cuts (fig. A)

• Adjust the saw to 0° bevel.

• Retract the blade guard using the lever (11) and

place the saw on the blade side.

• Loosen the bevel adjustment knob (6).

• Place a square against the blade and shoe to

adjust the 90° setting.

• Loosen the hex nut with a wrench and move the

adjustment screw so that the shoe will stop at

the proper angle. Secure the screw by tightening

the hex nut.

• If necessary, reset the pointer to “0”-position.

Replacing the saw blade (fig. C & D)

• Engage the blade lock button (4) and unscrew

the blade camping screw (9) by turning clockwise

using the Allen key supplied with the tool.

• Retract the lower blade guard (10) using the

lever (11) and replace the blade. Reinstall the

washers (19 & 20) in the correct position.

• Check the direction of rotation of the blade.

• Thread on the blade clamping screw (9) by hand

to hold the washer in position.

Turn counterclockwise.

• Press the blade lock button (4) while turning the

spindle until the blade stops rotating.

• Tighten the blade clamping screw firmly using the

Allen key.

Adjusting the riving knife (fig. E)

For the correct adjustment of the riving knife (8),

refer to the inset in figure E. Adjust the clearance of

the riving knife after changing the saw blade or

whenever necessary.

• Adjust the depth of cut to 0 mm to access the

fasteners of the riving knife.

• Loosen the fasteners and pull out the riving knife

to its maximum length.

• Adjust the clearance and tighten the fasteners.

DW936K2 - Fitting the parallel fence (fig. F)

• Fit the parallel fence (14) as shown.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Apply only a gentle pressure to the tool

and do not exert side pressure on the

saw blade.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

Prior to operation:

• Make sure your battery pack is (fully) charged.

• Make sure the guards have been mounted

correctly. The saw blade guard must be in closed

position.

• Make sure the saw blade rotates in the direction

of the arrow on the blade.

• Do not use excessively worn saw blades.

Switching ON and OFF (fig. A)

For safety reasons the ON/OFF-switch (1) of your

Trim Saw is equipped with a lock-off button (2).

• Press the lock-off button to unlock the tool.

• To run the tool, press the ON/OFF-switch.

As soon as the ON/OFF-switch is released the

lock-off switch is automatically activated to

prevent unintended starting of the machine.

Do not switch the tool ON or OFF when

the saw blade touches the work piece or

other materials.

Holding and guiding the Trim Saw (fig. A)

• Hold your DEWALT Power Tool by the main grip

and the front handle (3) to guide the saw

properly.

• For optimum results, clamp the workpiece

bottom up.

• Use the kerf indicator (7) to follow the line drawn

on the workpiece. The kerf indicator lines up with

the left (outer) side of the saw blade.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW935K T1-2 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info