Bedienungsanleitung DeWalt DW955 T 2 (Seite 23 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

549658

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

18 en - 5

ENGLISH

Do not charge the battery pack at

ambient temperatures <4 °C or >40 °C.

Recommended charging temperature:

approx. 24 °C.

• To charge the battery pack (6), insert it into the

charger (8) as shown and plug in the charger.

Be sure that the battery pack is fully seated in the

charger. The red charging indicator (9) will blink.

After approx. 1 hour, it will stop blinking and

remain on. The battery pack is now fully charged.

The battery pack can be removed at any time or

left in the connected charger indefinitely.

Inserting and removing the battery pack

• Insert the battery pack into the grip until it clicks

in place.

• To remove the battery pack, press the two

release buttons (7) simultaneously and pull the

pack out of the grip.

Inserting and removing bits (fig. A)

• Open the chuck (4) by turning the sleeve (5)

counterclockwise and insert the bit shank.

• Place the bit in the chuck as far as it will go and

lift slightly before tightening.

• Tighten firmly by turning the sleeve clockwise

while holding the rear part of the chuck with one

hand.

• To remove the bit, proceed in reverse order.

Forward/reverse switch (fig. A)

• To select forward or reverse rotation, use the

forward/reverse slider (2) as shown (see arrows

on tool).

Always wait until the motor has come to

a complete standstill before changing the

direction of rotation.

Two gear selector (fig. B)

Your tool is fitted with a two gear selector (3) to vary

the speed/torque ratio.

1 low speed/high torque

(drilling large holes, driving large screws)

2 high speed/low torque

(drilling smaller holes, driving smaller screws)

For speed rates, refer to the technical data.

Always push the two gear selector

completely forward or backward.

• Do not change gears at full speed or during use.

Removing and fitting the chuck (fig. C & D)

• Open the chuck jaws as far as possible.

• Insert a screwdriver into the chuck and remove

the chuck retaining screw (10) by turning

clockwise as shown in figure C.

• Tighten an Allen key into the chuck and strike it with

a hammer as shown in figure D. This will loosen the

chuck so that it can be unscrewed by hand.

• To refit the chuck, proceed in reverse order.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool.

Excessive force does not speed up

drilling but decreases tool performance

and may shorten tool life.

• To minimise stalling on break-through,

progressively reduce the drill point

pressure towards the end of the

operation.

• Keep the motor running when pulling the

bit back out of a drilled hole. This will

help prevent jamming.

Prior to operation:

• Make sure your battery pack is (fully) charged.

• Insert the appropriate bit.

• Mark the spot where the hole is to be drilled.

• Select forward or reverse rotation.

Switching ON and OFF (fig. A)

• To run the tool, press the variable speed switch (1).

The pressure exerted on the variable speed

switch determines the tool speed.

• To stop the tool, release the switch.

• To lock the tool in OFF-position, move the

forward/reverse slider (2) to the central position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW955 T 2 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info