Bedienungsanleitung DeWalt DW957 (Seite 24 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

447155

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

After approx. 4 hours, it will switch to maintenance

charge mode. The battery pack can be removed at

any time or left in the connected charger indefinitely.

• The red charging indicator flashes rapidly to

indicate a charging problem. Reinsert the battery

pack or try a new one. If the new pack also

refuses to charge, have your charger tested by

an authorised DEWALT repair agent.

• When plugged into power sources such as

generators or sources that convert DC to AC,

the red charging indicator may blink twice, switch

off and repeat. This indicates a temporary

problem of the power source. The charger will

automatically switch back to normal operation.

Do not charge the battery pack at

ambient temperatures < 4 °C or > 40 °C.

Recommended charging temperature:

approx. 24 °C.

Inserting and removing the battery pack

• Insert the battery pack into the grip (8) until it

clicks in place.

• To remove the battery pack, press the two

release buttons (10) simultaneously and pull the

pack out of the grip (8).

Equalisation mode

The equalisation mode helps to maintain the

optimum capacity of the battery pack. It is therefore

recommended to use the equalisation mode weekly

or every 10 charge/discharge cycles.

• Charge the battery pack as described above.

• When the charging indicator stops blinking, leave

the battery in the charger for approx. 4 hours.

DE9108/DE9116 - Hot Pack Delay

When the charger detects a battery that is hot,

it automatically starts a Hot Pack Delay, suspending

charging until the battery has cooled. After the

battery has cooled, the charger automatically

switches to the pack charging mode. This feature

ensures maximum battery life. The red indicator (12)

blinks long, then short while in the Hot Pack Delay

mode.

Inserting and removing bits (fig. A & B)

• Open the chuck by turning the sleeve (13)

counterclockwise and insert the bit shank.

• Place the bit in the chuck as far as it will go and

lift slightly before tightening.

• Tighten firmly by turning the sleeve clockwise.

• To remove the bit, proceed in reverse order.

Selecting the operating mode or adjusting the

torque (fig. C)

The collar of this tool has 17 positions for the

adjustment of the torque to suit the size of the screw

and the workpiece material. For torque adjustment,

refer to the section «Screwdriving».

• Select the drilling mode or torque by aligning the

symbol or number on the collar (4) with the

indicator (14) on the housing.

Forward/reverse slider (fig. D)

• To select forward or reverse rotation, use the

forward/reverse slider (2) as shown (see arrows

on tool).

Always wait until the motor has come to

a complete standstill before changing the

direction of rotation.

Two gear selector (fig. E)

Your tool is fitted with a two gear selector (3) to vary

the speed/torque ratio.

1 low speed/high torque

(drilling large holes, driving screws)

2 high speed/low torque

(drilling smaller holes)

For speed rates, refer to the technical data.

Always push the two gear selector

completely forward or backward.

• Do not change gears at full speed or during use.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW957 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info