Bedienungsanleitung DeWalt DW958K T 1 (Seite 27 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

549630

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISH

21 en - 6

2 high speed/low torque

(drilling smaller holes)

For speed rates, refer to the technical data.

• Always push the two gear selector

completely forward or backward.

• Do not change gears at full speed or

during use.

Removing and fitting the chuck (fig. F & G)

• Open the chuck jaws as far as possible.

• Insert a screwdriver into the chuck and remove

the chuck retaining screw by turning clockwise

as shown in figure F.

• Tighten an Allen key into the chuck and strike it

with a hammer as shown in figure G. This will

loosen the chuck so that it can be unscrewed

by hand.

• To refit the chuck, proceed in reverse order.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework

and wiring.

• Apply only a gentle pressure to the tool.

Excessive force does not speed up

drilling but decreases tool performance

and may shorten tool life.

• To minimise stalling on break-through,

progressively reduce the drill point

pressure towards the end of the operation.

• Keep the motor running when pulling the

bit back out of a drilled hole. This will

help prevent jamming.

Prior to operation:

• Make sure your battery pack is (fully) charged.

• Insert the appropriate bit.

• Mark the spot where the hole is to be drilled.

• Select forward or reverse rotation.

Switching ON and OFF (fig. A & D)

• To run the tool, press the variable speed switch (1).

The pressure exerted on the variable speed switch

determines the tool speed.

• To stop the tool, release the switch.

• To lock the tool in OFF-position, move the

forward/reverse slider (2) to the central position.

The drill is equipped with a brake to stop

the tool as soon as the variable speed

switch is fully released.

Screwdriving (fig. A)

• Select forward or reverse rotation using the slider (2).

• Set the collar (4) to position 1 and begin

screwdriving (low torque).

• If the clutch ratchets too soon, adjust the collar

to increase the torque as required.

Drilling (fig. A)

• Select the drilling mode using the collar (4).

Drilling in metal

• Use a cutting lubricant when drilling metals.

The exceptions are cast iron and brass which

should be drilled dry.

Drilling in wood

• Holes in wood can be made with the same twist

drills used for metal. These bits may overheat

unless pulled out frequently to clear chips from

the flutes.

• For larger holes use Auger bits.

• Use a block of wood to back up workpieces that

may splinter.

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT Power Tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Lubrication

Your Power Tool requires no additional lubrication.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW958K T 1 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info