Bedienungsanleitung DeWalt DW976 (Seite 25 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

447175

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Always release the variable speed switch

and wait until the motor has come to a

complete standstill before changing the

direction of rotation.

Two gear selector (fig. C)

Your tool is fitted with a two gear selector (3) to vary

the speed/torque ratio.

1 low speed/high torque

(drilling large holes or driving large screws)

2 high speed/low torque

(smaller holes, drilling in wood)

For speed rates, refer to the technical data.

Always push the two gear selector

completely forward or completely back.

Do not change gears at full speed or

during use.

Removing and fitting the chuck (fig. E & F)

• Open the chuck jaws as far as possible.

• Tighten an Allen key (14) into the chuck and

strike it with a hammer as shown in figure E.

• Insert a screwdriver into the chuck and remove

the chuck retaining screw by turning clockwise.

• Tighten an Allen key (14) into the chuck and

strike it with a hammer as shown in figure F.

This will loosen the chuck so that it can be

unscrewed by hand.

• To refit the chuck, proceed in reverse order.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool.

Excessive force does not speed up

drilling but decreases tool performance

and may shorten tool life.

Prior to operation:

• Insert the appropriate bit.

• Mark the spot where the hole is to be drilled.

• Make sure your battery pack is (fully) charged.

• Select forward or reverse rotation.

Switching on and off (fig. A)

• To run the tool, press the variable speed switch (1).

The pressure exerted on the variable speed switch

determines the tool speed.

• To stop the tool, release the variable speed

switch (1).

• To lock the tool in OFF-position, move the

forward/reverse slider (2) to the central position.

Screwdriving (fig. C & D)

• Select forward or reverse rotation using the

slider (2).

• Use the low speed/high torque position

(1st gear) (3).

• Set the torque adjustment collar (4). The higher

the number on the collar, the higher the torque

and the larger the fastener which can be driven.

Hammerdrilling (fig. C)

• Select the hammer mode.

• Press the variable speed switch (1).

• To stop the tool, release the switch.

Drilling (fig. C)

• Select the drilling mode.

• Proceed as described for hammerdrilling.

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT Power Tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

• Unplug the charger before cleaning the housing

with a soft cloth.

• Remove the battery pack before cleaning your

Power Tool.

ENGLISH

21 en - 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW976 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info