Bedienungsanleitung DeWalt DW979 T-1 (Seite 26 von 97) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

551289

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

ENGLISH

en - 6

Two gear selector (fig. A)

Your tool is fitted with a two gear selector (5) to vary

the speed/torque ratio.

1 low speed/high torque

2 high speed/low torque

For speed rates, refer to the technical data.

Always push the two gear selector

completely forward or completely back.

Do not change gears at full speed or during use.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Apply only a gentle pressure to the tool.

Excessive force does not speed up

screwdriving but decreases tool

performance and may shorten tool life.

• Follow the recommendations for the

appropriate driving speeds provided by

the manufacturers of self-drilling screws.

Prior to operation:

• Make sure your battery pack is (fully) charged.

• Insert the appropriate drive accessory.

• Select forward or reverse rotation.

• Set the appropriate driving depth.

Switching ON and OFF (fig. A)

• To run the tool, press the variable speed switch (1).

The pressure exerted on the variable speed

switch determines the tool speed.

• To stop the tool, release the variable speed

switch (1).

• To lock the tool in OFF-position, move the

forward/reverse slider (2) to the central position.

Screwdriving

• For best results, hold the screwdriver with the

hand directly in line with the fastener and press

the variable speed switch with the last one or two

fingers of the hand. This reduces the chance of

the screw slipping from the drive accessory when

pressure is applied.

• To drive the fastener, place it on the bit or into

the socket or nutsetter, press the variable speed

switch and push the fastener into the workpiece

with a smooth, continuous motion.

When the fastener is seated, the clutch will

disengage automatically.

Various types of 1/4" hex. bits, holders, sockets and

adaptors are available as an option.

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT Power Tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Lubrication

Your Power Tool requires no additional lubrication.

Cleaning

• Unplug the charger before cleaning the housing

with a soft cloth.

• Remove the battery pack before cleaning your

Power Tool.

• Keep the ventilation slots clear and regularly

clean the housing with a soft cloth.

Environment

Rechargeable battery pack

This long life battery pack must be recharged when

it fails to produce sufficient power on jobs which

were easily done before. At the end of its technical

life, discard it with due care for our environment:

• Run the battery pack down completely, then

remove it from the tool.

• NiCd cells are recyclable. Take them to your dealer

or a local recycling station. The collected battery

packs will be recycled or disposed of properly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW979 T-1 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info